Specifications - Jacuzzi Whirlpool Bath BUILDER Serie Manual De Instalación Y Operación

Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for
whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath
by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the
bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for
shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of
warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath must
be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool
Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.
L
SIDE VIEW
BATHS WITHOUT INTEGRAL SKIRT
L
SIDE VIEW
BATHS WITH 3-SIDED TILE FLANGE

SPECIFICATIONS

(Rectangular)
MODEL DIMENSIONS
AMIGA™
72" (1829 mm) L
36" ( 914 mm) W
20-3/4" ( 527 mm) H
BIANCA™
72" (1829 mm) L
48" (1219 mm) W
20-1/2" ( 521 mm) H
CETRA™
60" (1524 mm) L
WITH INTEGRAL
32" ( 813 mm) W
SKIRT
20-1/2" ( 521 mm) H
CETRA™ 536
60" (1524 mm) L
36" ( 914 mm) W
21-1/4" ( 553 mm) H
CETRA™ 536
60" (1524 mm) L
WITH INTEGRAL
36" ( 914 mm) W
SKIRT
21-1/4" ( 553 mm) H
CIVA™
60" (1524 mm) L
36" ( 914 mm) W
21-1/4" ( 540 mm) H
*Add 1/4" to this dimension when roughing-in for 3-wall niche.
FOR ALL UNITS:
MOTOR/PUMP: 115 VAC, 3450 RPM/10 AMP, 60 Hz Single phase.
ELECTRICAL REQUIREMENTS: 115 VAC, 15 AMP, 60 Hz. Requires dedicated separate circuit.
W
2"
51 mm
H
END VIEW
W
1"
25.4 mm
H
END VIEW
DRAIN/OVERFLOW
DRAIN/OVERFLOW
CUTOUT
DIMENSIONS
70" x 34"
* 16-7/8" (429 mm) A
14" (356 mm) B
16" (406 mm) A 70" x 46"
*
8-1/2" (216 mm) B
17-7/8" (454 mm) A NA
*
9-3/8" (238 mm) B
58"
* 18-1/2" ( 470 mm) A
X
9" ( 229 mm) B
34-1/4"
18-1/2" ( 470 mm) A NA
*
9" ( 229 mm) B
* 16-3/4" (426 mm) A 58" x 34"
9-3/8" (238 mm) B
L
SIDE VIEW
BATHS WITH INTEGRAL SKIRT
L
SIDE VIEW
BATHS WITH 4-SIDED TILE FLANGE
A
B
TOTAL WEIGHT/ OPERATING
FLOOR LOADING GALLONAGE
50 U.S. gal
797 lb
(186 liters)
(362 kg)/
45 lb/sq. ft.
(220 kg/sq. m)
1143 lb 73 U.S. gal
(519 kg)/ (276 liters)
48 lb/sq. ft.
(234 kg/sq. m)
46 U.S. gal
719 lb
(174 liters)
(326 kg)/
54 lb/sq. ft.
(263 kg/sq. m)
48 U.S. gal
700 lb
(181 liters)
(318 kg)/
56 lb/sq. ft.
304 kg/sq. m
48 U.S. gal
720 lb
(181 liters)
(327 kg)/
48 lb/sq. ft.
234 kg/sq. m
44 U.S. gal
700 lb
(167 liters)
(318 kg)/
47 lb/sq. ft.
(229 kg/sq. m)
2
1"
25.4 mm
H
1"
25.4 mm
H
AVAILABILITY OF
PRODUCT
SKIRT & "RAPIDHEAT"
WEIGHT MOUNTING
IN LINE HEATER
Optional,
105 lb Yes
U-Frame
(48 kg)
135 lb Optional, Yes
(61kg) U-Frame
Integral Yes
125 lb
(57 kg)
Yes
Optioal
92 lb
U Frame
(42 kg)
Integral
130 lb
Yes
(59 kg)
92 lb Optional, Yes
(42 kg) U-Frame
W
END VIEW
W
END VIEW