Gastro GW 35 Serie Instalación, Uso, Mantenimiento página 21

IF IT IS NECESSARY TO OPEN THE DOOR
WHEN THE MACHINE IS RUNNING
AVOID DOING IT TOO QUICKLY.
Although the appliance is equipped with a safety
switch to prevent the door from opening suddenly,
spurts of water could still reach the user in the event
of a hasty manoeuvre.
NORMAL OPERATING CYCLE:
Once the machine is ready to operate as per the "
COMISSIONING" paragraph, follow the instructions
below to run the desired wash cycles :
Insert the rack with the soiled crockery and close the
-
door;
Select the long or quick cycle switch (6) press the
cycle (3) start-up button. The indicator light (4) will
-
illuminate when the machine has started the selected
wash cycle.
In case of accidental door opening the washing cycle
will stop and the pilot light (4) will flash at intervals (1
-
sec. ). Once the door will be closed again, the cycle
will restart from where it has been interrupted.
Once the cycle has finished, the indicator light (4) will
-
switch off.
Open the door, extract the rack with the clean
crockery and insert another rack, which has been
-
previously loaded, into the dishwasher for the next
wash cycle.
At least twice a day, or if you notice turbidity and
thickening of the washing water due to excessive
concentration of dirt particles in suspension, it is
ESSENTIAL to renew it.
Washing in these conditions causes wasteful
increasing of detergent and energy, to the detriment
of the quality of washing.
DRAINAGE PUMP
The exceeding water which enters the bowl at the
start of a rinse cycle is automatically drained.
Follow the instructions below to drain the bowl
completely:
- Remove the overflow (not the filter)
Switch off the machine by pressing the ON-OFF (1)
-
switch
Press button 3 to start the draining cycle, the lamp
- (4) turns on, blinks for 3 seconds and the draining
cycle continue for 2 min. and 20 sec.
At this point you can remove the filter tank for
-
cleaning.
In models equipped
decalcification system and drainage pump, the water
is automatically drained from the bowl during the
regeneration cycle.
with an inlet water
COLD RINSE
Washers with traditional cycle offer you the
possibility of using an additional rinse cyce with net
temperature water. Once the washing ends (cycle
alarm 4 off) prosceed as follows:
- Make sure the door is closed, then press 9 button.
Keep the button pressed for the desidered time, then
-
release it.
- Wait a few seconds before pulling the basket out.
DECALCIFICATION AND REGENERATION OF RESINS
Some dishwasher models are equipped with a system
for water decalcification and the regeneration of ion
exchange resins in salt water.
DECALCIFICATION : the system is designed for
decalcifying the inlet water that runs through the
boiler (without any external intervention).
REGENERATION OF RESINS: a regeneration of ion
exchange resins in the water softener is required at
regular intervals depending on the hardness of the
inlet water (see table) and must be carried out as
follows:
The machine is set to do the regen program every 60
washing cycles; the warning light (8) will start to blink
when the regen program is requested. You can stop
the blinking only by starting the regen program.
Switch off the machine by pressing the ON-OFF (1)
-
switch
Remove the overflow to drain the bowl (for
- equipment with drain pump press the button (7) the
draining and regeneration will start on sequence.
Once the bowl is empty, unscrew the threaded cap
(located inside at the bottom of the bowl) and pour
-
in 1 kg of sodium chloride (large-grained kitchen salt).
One load is generally sufficient for ¾ regeneration.
Close the door and press button (7) until indicator
-
light (8) remains on.
In case of accidental door opening the regenerating
cycle will stop and the pilot light (8) will flash at
- intervals (1 sec. ). Once the door will be closed again,
the cycle will restart from where it has been
interrupted.
After approximately 20 minutes indicator light (8)
- switches off signalling that the regeneration cycle has
terminated.
Normal operation can be resumed by following the
-
instructions at paragraph "SETTING IN OPERATION"
N. B. : It is advisable to perform the regeneration
process during periods in which the machine is not
used. Failure to carry out the regeneration process
according to pre-defined intervals will cause the
decalcifier to clog up and the amount of water
supplied to the rinse jets to decrease.
21