Noise/Vibration Information; Ec Declaration Of Conformity; Battery Charging - Würth STP 12-A Traducción Del Manual De Instrucciones De Servicio Original

OBJ_BUCH-2273-002.book Page 18 Friday, May 20, 2016 11:38 AM
Cordless Jigsaw
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
2)
– during operation
and during storage
Recommended batteries
Recommended chargers
1) depending on the battery pack being used
2) Limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 77 dB(A); sound power level 88 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-11:
2
Sawing chipboard: a =5.5 m/s
h
Sawing sheet metal: a =5.0 m/s
h
The vibration level given in this information sheet has been meas-
ured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents the main appli-
cations of the tool. However if the tool is used for different appli-
cations, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
EC-Declaration of Conformity
We declare under our sole responsibility that the product
described under "Tool Specifications" complies with all
applicable provisions of the directives 2009/125/EC
(Regulation 1194/2012), 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and is in conform-
ity with the following standards:
EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
STP 12-A
Adolf Würth GmbH & Co. KG, Abt. PPT,
Reinhold-Würth-Straße 12–17
1)
kg 1.5–1.7
74653 Künzelsau, Germany
°C 0...+45
°C –20...+50
AKKU-LI 12V/x.x Ah
Frank Wolpert
AL 30-LI
General Manager
Künzelsau: 01.06.2016
 Use only the chargers listed in the tool specifi-
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the first
time.
The lithium-ion battery can be charged at any time without
2
reducing its service life. Interrupting the charging procedure
, K=1.5 m/s ,
2 2 does not damage the battery.
, K=1.5 m/s .
Observe the notes for disposal.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator 5
show the charging status of the battery 1. The battery charge-
control indicator only illuminates for 5 seconds after start-up.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Flashing light 3 x green
When no LED lights up after switching on, then the battery is
defective and must be replaced.
Removing the battery (see figure A)
To remove the battery 1 press the unlocking buttons 2 and
pull out the battery downwards. Do not exert any force.
Dr.-Ing. Siegfried Beichter
General Manager

Battery Charging

cations. Only these chargers are matched to the lithium-
ion battery of your power tool.
Capacity
2/3
1/3
<1/3
Reserve
Empty
18