Matrix T-DPT Manual Del Usuario página 6

LEVELING THE EQUIPMENT
It is extremely important that the levelers are correctly adjusted
for proper operation. An unbalanced treadmill may cause belt
misalignment or other issues. Use of a level is recommended.
Once you have placed the treadmill where you intend to use it, raise or lower
one or both of the adjustable levelers located on the bottom-front of the frame.
PROPER USAGE
SLED MODE
PROPER USAGE
The treadmill can be used in two modes; sled or walk/sprint. To use the
treadmill in sled mode, remove the harness so the user has access to the
upper and lower sled handlebars. To use the treadmill in walk / sprint
mode, connect the harness and adjust by using the instructions below.
Emergency dismount can be done by grabbing the front or side
handlebars and jumping with both feet on the side rails.
SLED MODE ADJUSTING THE HARNESS
After stepping onto the treadmill, slowly walk into the harness to check for
proper height. The harness should sit comfortably at about waist height.
If the harness needs to be adjusted, release the front connection
point and reconnect the harness at the correct height.
ADJUSTING THE BRAKES
The treadmill is equipped with two brakes, a sled brake and a speed brake. The
left hand side lever controls the sled brake and the right hand lever controls the
speed brake. The sled brake has 8 resistance settings and the speed brake has 11.
The brakes are designed to be used together or independently of each other.
The sled brake is designed to simulate the resistance created when pushing a
sled. When using this brake, resistance will be immediately applied to the belt.
The speed brake is designed to simulate the resistance created
when running with a parachute. When using this brake,
resistance will increase as the user increases speed.
SLED BRAKE
(LEFT SIDE)
10
MX15_T-DPT_TREADMILL_OM_r1_0_MULTI.indd 10-11
MAINTENANCE
1. Any and all part removal or replacement must be performed by a qualified service technician.
2. DO NOT use any equipment that is damaged and or has worn or broken parts.
Use only replacement parts supplied by your country's local MATRIX dealer.
3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain
important information. If unreadable or missing, contact your MATRIX dealer for a replacement.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to
smooth operating equipment as well as keeping your liability to a
WALK / SPRINT
PROPER USAGE minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance
or repair of any kind is qualified to do so. MATRIX dealers will provide service
and maintenance training at our corporate facility upon request.
WARRANTY
For North America, please visit www.matrixfitness.com for warranty
information along with warranty exclusions and limitations.
WALK / SPRINT MODE
HARNESS
PRODUCT SPECIFICATIONS
Max User Weight
Product Weight
Shipping Weight
Overall Dimensions
(L x W x H)*
SPEED BRAKE Max. Harness Loading
(RIGHT SIDE)
* Ensure a minimum clearance width of 0.6 meters (24") for access to and
passage around MATRIX equipment. Please note, 0.91 meters (36") is the
ADA recommended clearance width for individuals in wheelchairs.
MAINTENANCE SCHEDULE
ACTION
Clean entire machine using water and a mild soap
or other Matrix approved solution (cleaning agents
should be alcohol and ammonia free).
Check harness for wear and secure connections.
Remove the front cover. Check for debris and clean
with a dry cloth or small vacuum nozzle.
Lubricate treadmill running deck
RUNNING
DECK
LUBRICATING THE RUNNING BELT
181.4 kg / 400 lbs
1. Using a T-wrench or Allen wrench, loosen the rear roller bolts
141.2 kg / 312 lbs
10-15 counter-clockwise turns. This should give
the belt enough slack for you to lift it.
158.2 kg / 349 lbs
2. Lift the belt as far as you can and squirt the silicone oil in a zigzag
pattern across the entire running deck surface. Use 1/2 bottle of
193 x 88 x 150 cm /
100% silicone oil lubricant. Do not apply the silicone oil on top of
76" x 34.6" x 59"
the running belt. Lay the running belt down and then tighten both
136 kg / 300 lbs rear roller bolts clockwise the same number of turns loosened.
3. Walk on the machine at a comfortable speed for 3 minutes to spread the
silicone and to check the running belt for proper tension and alignment.
4. Wipe any excess oil from the sides with a damp cloth.
FREQUENCY
DAILY
DAILY
MONTHLY
EVERY 3 MONTHS
RUNNING
BELT
11
12/17/15 8:51 AM