Miter Cutting; Electrical Connection; Cleaning, Maintenance, Storage And Ordering Of Spare Parts; Ordering Replacement Parts - Toolson DKS1600 Traducción De Las Instrucciones Originales De Funcionamiento

8.6 Miter cutting

To carry out miter cuts adjust the distance of the
blade guard for worktable accordingly. Swivel the
saw table by loosening the locking lever (12) and tilt-
ing the table to the desired position (Fig. 12). Tighten
the locking lever.
Important.
Be especially careful when making miter cuts. The
angle of the saw table makes it easier for the work-
piece to slip. Risk of injury.

9. Electrical connection

The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these regu-
lations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking H 05 VV-F.
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 220-240 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician. Please provide
the following information in the event of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
24 GB
10. Cleaning, maintenance, storage
and ordering of spare parts
Important.
Always pull out the power plug before starting any
cleaning work.
10.1 Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
• We recommend that you clean the equipment im-
mediately after you use it.
• Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
10.2 Servicing
There are no parts inside the equipment which re-
quire additional maintenance.
10.2.1 Bearing(s) (Fig. 1/Item 8)
Periodically lubricate the bearings (8) of the guide
rollers with high-grade machine grease, at the latest
however after 25 to 30 hours of operation.
10.2.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician. Im-
portant: The carbon brushes should not be replaced
by anyone but a qualified electrician.
10.3 Storage
Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing tem-
perature. The ideal storage temperature is between 5
and 30 °C. Store the electric tool in its original pack-
aging.

10.4 Ordering replacement parts

The following information must be provided on all or-
ders for spare parts:
• Model/type of the equipment
• Article number of the equipment
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, table liners,
V-belts
* Not necessarily included in the scope of delivery!