pizzato FD 874 Guia De Inicio Rapido página 5

Example E
VF AF-CA10
VF F05
VF AF-IFGR03
VF AF-MR5
VF AF-TR8
3 m max 3 m max
4.4 Rope tightening
The maximum rope lengths listed in paragraph INSTALLATION EXAMPLES are
reduced, if the ambient temperature is subject to considerable variations.
The max. recommended lengths are indicated in the following diagram in accordance
with the temperature fluctuations (temperature differences) to which the switch may
be exposed at the point of use.
The values indicated in the graph are guaranteed only for use of the original rope and
accessories.
30
Example A
25
20
Example B
15
Example C, E
10
Example D
5
0
0 10 20 30
Temperature difference ΔT (°C)
4.5 Electrical connections
Attention: The safety circuit must be connected to NC contacts 11 - 21; contacts
12 - 22 must be connected in series, as shown in the following
A A
3
11 12
11
21
2
1
5 OPERATION
Once you have affixed the device to the machine, connected and tensioned
the actuation rope, and made the electrical connections as described in the
"INSTALLATION INSTRUCTIONS" paragraph, pulling on the rope must cause the
electrical contacts inside the device to open.
6 INSTRUCTIONS FOR PROPER USE
6.1 Installation
- Tighten the fixing screws of electrical conductors to a torque from 0.6 to 0.8 Nm.
- Do not stress the device with bending and torsion.
- Do not modify the device for any reason.
- Do not exceed the tightening torques specified in the present manual.
- The device carries out an operator protection function. Any inadequate installation
or tampering can cause serious injuries and even death, property damage, and
economic losses.
- These devices must not be bypassed, removed, turned or disabled in any other way.
- If the machine where the device is installed is used for a purpose other than that
specified, the device may not provide the operator with efficient protection.
- The safety category of the system (according to EN ISO 13849-1), including the
safety device, also depends on the external components connected to it and their
type.
- Before installation, make sure the device is not damaged in any part.
- Avoid excessive bending of connection cables in order to prevent any short circuits
or power failures.
- Do not paint or varnish the device.
- Do not drill the device.
- Do not use the device as a support or rest for other structures, such as raceways,
40 50 60 70 80 90
diagram.
Legend
B C
1 Start button
2 Stop button
3 Fuse
11 12
12
A Tensioned rope
22 21 22
B Cut or disconnected rope
C Pulled rope
sliding guides or similar.
- Before commissioning, make sure that the entire machine (or system) complies with
all applicable standards and EMC directive requirements.
- The fitting surface of the device must always be smooth and clean.
- The documents necessary for a correct installation and maintenance are always
available in the following languages: English, French, German and Italian.
- Should the installer be unable to fully understand the documents, the product must
not be installed and the necessary assistance may be requested (see paragraph
SUPPORT).
- Always attach the following instructions to the manual of the machine in which the
device is installed.
- These operating instructions must be kept available for consultation at any time and
for the whole period of use of the device.
6.2 Do not use in the following environments
- In environments where continual changes in temperature cause the formation of
condensation inside the device.
- In environments where the application causes collisions, impacts or strong vibrations
to the device.
- In environments containing explosive or inflammable gases or dusts.
- In environments where ice can form on the device.
- In environments containing strongly aggressive chemicals, where the products used
coming into contact with the device may impair its physical or functional integrity.
- Prior to installation, the installer must always ensure that the device is suitable for
use under the ambient conditions on site.
6.3 Maintenance and functional tests
Attention: Never disassemble or attempt to repair the device, rope, or acces-
sories. Should an anomaly or fault occur, replace the device, rope, or accessories.
Attention: Should the device, rope, or accessories become damaged or worn,
always replace them immediately. Correct operation cannot be guaranteed when the
device, rope, or accessories are deformed or damaged.
- The installer is responsible for establishing the sequence of functional tests to which
the device is to be subjected before the machine is started up and during mainte-
nance intervals.
- The sequence of the functional tests can vary depending on the machine complexity
and circuit diagram, therefore the functional test sequence detailed below is to be
considered as minimal and not exhaustive.
- Perform the following sequence of checks before the machine is commissioned and
at least once a year (or after a prolonged shutdown):
1) Check correct tensioning of the rope as described in the INSTALLATION INSTRUC-
TIONS paragraph.
100
2) Pull the rope when the machine is moving. The machine must stop.
3) Keeping the rope pulled, try to start the machine. The machine must not start.
4) Check that the rope is affixed to the stay bolts and end terminals correctly and, if
necessary, re-affix the rope as described in paragraph INSTALLATION INSTRUC-
TIONS.
5) All external parts must be undamaged.
6) Carefully check the condition of the external rope covering. If you discover cracks
or colour variations that could impede the function of the rope itself, replace the
entire rope.
7) Ropes, pulleys, terminals, jumpers, and stay bolts must be in good condition, and
firmly attached.
8) If the device or an accessory is damaged, replace it completely.
- The device and related accessories have been created for applications in dangerous
environments, and they therefore have a limited service life. After 20 years from the
production date, the device and related accessories must be replaced entirely; even
if they still work. The date of manufacture is positioned adjacent to the product code
(see paragraph MARKINGS).
6.4 Wiring
- Keep the charge within the values specified in the electrical operation categories.
- Only connect and disconnect the device when the power is off.
- During and after the installation do not pull the electrical cables connected to the
device. If traction is applied to the cables (not supported by an appropriate cable
gland) internal parts of the device may be damaged.
- Always connect the protection fuse (or equivalent device) in series to the safety
electrical contacts.
- At the end of the wiring, check that no contaminating element has been introduced
inside the device.
- Before closing the device cover verify the correct positioning of the gaskets.
- Verify that the electrical cables, wire-end sleeves, cable numbering systems and any
other parts do not obstruct the cover from closing correctly or if pressed between
them do not damage or compress internal parts.
- Adhere to the following minimum and maximum cross-sections of electrical
conductors designed for screw terminals:
min 1 x 0.5 mm (1 x AWG 20)
2
max 2 x 2.5 mm (2 x AWG 14)
2
- The stripping length of the cable or wire end sleeve must be 8 mm.
8 mm
6.5 Additional prescriptions for safety applications with operator protection
functions
Provided that all previous requirements for the devices are fulfilled, for installations
with operator protection function additional requirements must be observed.
- The utilization implies knowledge of and compliance with following standards:
EN 60947-5-3, EN ISO 13849-1, EN 62061, EN 60204-1, EN ISO 14119,
EN ISO 12100.
5/18