VERTO 51G517 Manual De Instrucciones página 8

GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
Ul. Pograniczna 2/4
02-285 Warszawa
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna na platformie internetowej gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz
materiałów eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl. Zeskanuj kod QR i wejdź:
tel. +48 22 573 03 85
fax. +48 22 573 03 83
e-mail service@gtxservice.pl
do napraw gwarancyjnych
GB
TRANSLATION OF THE ORIGINAL
INSTRUCTIONS
HOT AIR GUN
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SPECIFIC REGULATIONS REGARDING SAFE USE OF HOT AIR GUN
This equipment is not designed for use by persons (including
children) with limited physical, sensory or mental abilities, persons
with insufficient experience or knowledge about device, unless under
supervision or acting in accordance with instructions regarding use
of equipment provided by persons responsible for their safety. Pay
attention to children, do not allow to play with the equipment.
Careless handling of the hot air gun may cause fire, therefore:
– be careful when using the hot air gun in places, where flammable
materials are present;
– do not direct stream of hot air onto the same place for a long time;
– do not use hot air gun in explosive atmosphere;
– bear in mind that heat can transfer to flammable materials that
are beyond field of view;
– leave the hot air gun to cool down after use and before storing;
– do not leave the hot air gun unattended.
ADDITIONAL SAFETY RULES
• Use protective goggles when operating the hot air gun.
• Do not obstruct air intake holes or outlet nozzle hole of the hot air gun.
• Do not touch nozzle of the hot air gun during operation or just after.
• Keep the hot air gun handle clean, do not allow traces of oil or grease.
• When working outdoors do not use hot air gun when it is raining
or in high humidity.
• Do not put the hot air gun away when it is switched on.
• Do not direct flow of hot air from the gun at one point for a long time.
• Always switch off the hot air gun with its switch before removing
the power cord plug from mains socket.
• Remove particles of paint deposited on the nozzle of hot air gun
from time to time to prevent spontaneous ignition.
• Prior to commencing any tasks with hot air gun, always ensure that
the surface to be heated is not flammable.
• Removing oil paint that contains lead can be carried out in rooms
with good ventilation only. Vapours of such paints are poisonous.
Use mask for protection of respiratory system.
• When using hot air gun do not use agents such as turpentine,
solvents or petrol.
• Do not touch hot parts of the gun just after its operation has been
finished. Burns resulting from negligence of these rules constitute
main hazard when working with hot air gun.
• Never point operating hot air gun at any person or animal (e.g. to
dry hair). Hot air gun produces much higher temperature than hair
dryer does.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of operational injuries.
CONSTRUCTION AND USE
Hot air gun is a hand-held power tool with insulation class II. Double
insulation of the hot air gun and integrated protection against
overheating (thermal switch) ensure safe operation. It is equipped
with AC motor that drives small turbine inside, which forces air to flow
through heating element. Stream of air is then directed through outlet
nozzle towards processed surface. Design of the hot air gun allows
to use one of the tempeerature ranges to adjust air temperature for
requirements of the task. Hot air gun is designed for paint coating
removal, heating up stuck threaded joints to aid in unscrewing and to
heat up frozen water piping, locks, padlocks etc. Hot air gun can also
be used for drying wooden elements before mechanical processing,
8
51G517