Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installing Universal Tilt Wall Mount to Metal Stud Walls
(Metal Stud Accessory Kit ACC 215 Required)
• Drywall must be 1/2" (13 mm) or thicker, and metal stud must be 24 gauge or thicker.
• Make sure that the wall will safely support the combined load of the equipment and all attached hardware and
components.
Using a stud finder, locate and mark the edges of the metal stud used in mounting this product. Use of an edge to
1
edge stud finder is highly recommended. Use a level to draw a level, vertical line down the center of the stud. Level
tilt assembly (B), and mark the center of the two mounting holes. Make sure that the mounting holes are on the
stud centerlines. Drill two 1/2" (13 mm) holes through drywall and metal studs. NoTe: It may be necessary to drill
5/32" (4 mm) pilot holes prior to drilling 1/2" (13 mm) holes.
Refer to instruction sheet included with Peerless accessory kit ACC215 for metal studs to install togglers.
Loosely fasten tilt assembly (B) to wall using two 1/4-20 x 2-1/2" screws as shown. Level, hold, and then tighten all
screws.
Skip to step 2 of main instruction sheet.
1/4-20 x 2-1/2"
phILLIps screws
WARNING
toggLer
B
1 of 4
Models: ST632, ST632-S,
ST632P, ST632P-S,
RTFPT632, RTFPT632S,
SWV220/BK, SWS220/SI
ISSUED: 05-11-05 SHEET #: 201-9475MS-4 06-16-09
Publicidad
Manuales relacionados para Rehabmart ST632
Resumen de contenidos para Rehabmart ST632
- Página 1 Models: ST632, ST632-S, Installing Universal Tilt Wall Mount to Metal Stud Walls ST632P, ST632P-S, RTFPT632, RTFPT632S, (Metal Stud Accessory Kit ACC 215 Required) SWV220/BK, SWS220/SI WARNING • Drywall must be 1/2" (13 mm) or thicker, and metal stud must be 24 gauge or thicker.
- Página 2 Modelo: ST632, ST632-S, ST632P, Installation du support mural universel inclinable sur ST632P-S, RTFPT632, murs à colombage métallique RTFPT632S, SWV220/BK, (ensemble d’accessoires ACC215 pour poteaux métalliques requis) SWS220/SI ADVeRTeNCIA • el yeso-cartón tiene que tener un grosor de 1/2" (13 mm) o más y los montantes tienen que ser de calibre 24 o más.
- Página 3 Français Modèle: ST632, ST632-S, Installation de supports plats Paramount™ sur des murs à ST632P, ST632P-S, montants métalliques RTFPT632, RTFPT632S, (ensemble d’accessoires pour montants métalliques ACC215 requis) SWV220/BK, SWS220/SI AVeRTISSeMeNT • La cloison sèche doit avoir 13 mm (1/2 po) d’épaisseur ou plus et les montants métalliques doivent être de calibre 24 ou plus.
- Página 4 Deutsch Anbringung von Paramount™-Flachhaltern an Metall- Modelle: ST632, ST632-S, ST632P, ST632P-S, ständerwänden RTFPT632, RTFPT632S, (Metallständer-Zubehörsatz ACC215 erforderlich) SWV220/BK, SWS220/SI ACHTUNG • Die trockenwand muss 13 mm (1/2 Zoll) oder dicker sein, und der Metallständer muss 24 gauge oder dicker sein.