YATO YT-85090 Manual De Instrucciones página 20

GB
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply from the mains. In
addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (XV), the more LEDs, the more
the more battery is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Insert the battery in the charger socket, so that the latches secure the battery into the socket (XVI).
The charging station has two LEDs, green and red. They show the status of operation:
- the red LED lights up - the battery is charging,
- the green LED lights up - the battery is charged,
- red and green LEDs light up at the same time - the temperature protection is on,
- red and green LEDs are blinking - the battery is damaged,
- green LED is flashing - there is no battery in the charging station.
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off, and green LED lights up, indicating the charging of charger.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button. You should remove the battery from the char-
ging station immediately after the end of the charging process. Leaving the battery in the mains connected power charging station
may result in its irreversible damage.
Due to the fast charging process the charging station has been equipped with a fan, which may turn on during the charging pro-
cess of the battery pack. Despite the operation of fan of charging station, the battery may become warm during charging. This is
normal. When you are loading the battery in a high temperature environment the temperature protection in charger can switch on.
The charging process is interrupted until the cooling of electronic systems of station, after that it is automatically resumed. In such
conditions, the battery charging time will be longer.
MAINTENANCE AND STORAGE OF THE PRODUCT
Attention! Before starting any operation, which is described below, you should disconnect the chain saw from the power supply.
Chain saw, which are mains powered, should be disconnected from the wall outlet, the chain saw, which are battery operated,
should be disconnect from the battery.
After each use, you should examine the chain saw condition, with a focus on the patency of ventilation openings.
Check the alignment of all elements of the chain saw. Any loose connections should be tightened. Check the voltage and condition
of the chain. If you notice any chain damage, the chain should be replaced with a new one. It is forbidden to operate the chain
saw with a damaged chain.
Too loose chain may fall out from its guide, which can cause injury to a person that operates the chain saw. The chain must also
be properly sharpened, because it requires the relevant experience and tools, it is recommended, to perform chain sharpening
in a specialist service. You should fill up the oil deficiencies in the tank. The chain saw housing should be cleaned with a soft dry
cloth. Clean the housing of residual wood, oil, grease and other contaminants. The chain saw should be stored in a dry, closed
room, disconnected from the mains.
Attention! During storage, the chain saw may produce a small amount of oil from the chain lubrication system, this is normal and
does not affect the oil level in the tank and is not a sign of failure.
The chain saw should be stored in the areas, which are shaded dry, and equipped with adequate ventilation to prevent conden-
sation. The place should not be available for bystanders, especially children. During storage the guide and chain should always
be protected by the cover.
O R I G I N A L I N S T R U C T I O N S
20