Chicco Bubble land Manual De Instrucciones página 12

part is broken, or missing.
• Do not use accessories, spare parts,
or any component not supplied or
approved by the manufacturer.
• This bath tub can be used alone
or on the changing unit frame up
to when the child tries to stand up
by itself.
• Stand alone bath cradles can be
used up to when your child can sit
unaided.
• This bath tub can be used on the
stand up to when the child tries to
stand up by itself.
• Always check the fastening and
stability of the tub on the chang-
ing table frame.
• Mix water to avoid spots that are
too hot or cold.
• Only an adult may wash the baby.
• Never turn the child on its stom-
ach inside the tub.
• Do not leave objects in the tub
when bathing.
• When using the tub make sure that
the plug has been fitted correctly.
• Ensure that all the locking devices
are engaged before placing the tub.
• Only one child may use the tub at
a time.
• Pay attention to appliances and
power cables near the product.
• When unused, the product should
be kept out of reach of children.
USING THE WASH TUB
WARNING: Perform these operations before
putting the baby inside the tub.
WARNING: Always check the temperature of
the water before putting your child in.
WARNING: Only drain the tub after the baby
has been removed.
The tub (B) supplied can be used in one of the
following ways:
Installed on the frame (A) (Fig. 13)
• To access the tub (B), turn the changing table
A3 over on its back (Fig. 14) after having re-
leased it.
• Before filling the tub (B), make sure that the cap
(B1) is installed correctly (Fig. 15), then fit the
drainage pipe (B2), connecting one end to the
tub (B) (Fig. 16) and the other end to the termi-
nal (B3) (Fig. 17). Fasten the terminal of the hose
on the side of the tub (Fig. 18). To empty the
tub (B), remove cap (B1) making sure to empty
the water into a drain.
On a flat surface or inside an adult bath tub
(Fig. 19)
• Before filling the tub (B), make sure that the cap
(B1) is fastened correctly (Fig. 15), taking care to
remove the drainage pipe (B2) (Fig. 20).
• Then proceed with filling of the tub (B).
To empty the tub (B), remove cap (B1) making
sure to empty the water into a drain.
CLOSING THE PRODUCT
To close the product:
1. Release the fastening clamp (A6) from the but-
ton (A7) (Fig. 21).
2. Turn the changing table (A3) to the back (Fig. 14).
3. Remove the tub (B) (Fig. 22).
4. Remove all objects on the shelf (A1).
5. Release the joints (A5) using the lever (Fig. 23)
and fold the frame (A) until it is fully closed
(Fig. 24).
6. Lock the changing table by attaching the fas-
tening clamp (A6) to the button (A7) (Fig. 25).
PRODUCT CLEANING AND MAINTENANCE
• The product can be cleaned with a moist clean-
ing cloth.
• Do not use solvents or abrasive products on
any of the surfaces.
• Always dry the metal parts to prevent the for-
mation of rust.
• It is possible to remove the cushioned pad (see
point 7) to clean it and the tub.
• To prevent mould from developing, take care to
dry the changing table after each time it is used.
WARRANTY
The product is guaranteed against any conform-
ity defect in normal conditions of use as de-
scribed in the instructions. The warranty shall not
therefore apply in the case of damage caused by
improper use, wear or accidental events. For the
duration of the warranty on conformity defects
please refer to the specific provisions of appli-
cable national laws in the country of pur chase,
where appropriate.
12