Rosenbauer HEROS-xtreme Manual Del Usuario página 13

Rosenbauer - User Guide HEROS-xtreme
User Guide
HEROS-xtreme Fire fighting helmet
INTRODUCTION
In these instructions for use, we provide you with all the necessary information
on design, employment and care of the HEROS-xtreme fire fighting helmet.
Despite strict quality requirements during the development and production
processes, as well as stringent final checks prior to every delivery, in the final
analysis, the HEROS-xtreme helmets are only as good as the standard of
their handling, maintenance and care. In other words, the extent to which the
HEROS-xtreme can fulfil its protective function and the subsequent degree of
user satisfaction are very much in the hands of the individual fire-fighter.
1. Safety instructions and fire fighting helmet applications
1.1 The HEROS-xtreme fire fighting helmet may only be used for the purposes
for which it has been designed after careful study of the complete instructions.
The helmet is to be employed exclusively for operations according to fire
fighting guidelines and standard practice.
The helmet is neither suitable nor certificated for uses, e.g. as a cycle helmet,
motor cycle helmet, as a seat, as an object for standing on, or similar activities.
Utilisation for such purposes is unacceptable and forbidden.
WARNING: Improper use of the helmet for purposes other than
those permitted can lead to serious injury!
1.2 The HEROS-xtreme fire fighting helmet must be handled, checked
and maintained in the manner described in this user information and the
instructions for use. In order to safeguard the HEROS-xtreme helmet against
premature ageing, store it in a place, which offers maximum protection against
light and moisture (e.g. wall cupboard, etc.).
1.3 All repair work, component exchange and servicing on the HEROS-xtreme
fire fighting helmet may only be undertaken according to the appropriate
guidelines pursuant to these instructions for use. All activities must be logged.
Only specialists authorised by ROSENBAUER may carry out fundamental
maintenance and servicing work, not described in this user information.
24 24
1.4 At the very least, the helmet shell and the interior harness must be
checked for possible damage, either before or after each operation. In
particular, the tight fit of all screws (especially those on the locking straps) is
to be examined. In the case of unusual damage (loads) on the helmet shell,
the interior harness, the chinstrap or other parts, these must be exchanged
in order to guarantee the defined protective function. Only original parts may
be employed for the maintenance of the HEROS-xtreme fire fighting helmet.
Subsequently applied paint on the helmet surface, or stickers not approved
by Rosenbauer, can alter the characteristics of the material and are either
forbidden, or subject to prior approval from Rosenbauer. No alterations may be
made to the helmet shell and the interior harness.
WARNING: Changes to the helmet shell or interior harness can
have a negative effect on helmet function and thus cause serious
injury. Therefore, they are forbidden.
1.5 During operations in areas subject to the danger of explosions, the
breathing apparatus mask and the helmet should be treated with antistatic
spray, Art. No. 401228, or a water film should be applied.
1.6 The responsibility and liability for the aforementioned items 1.1-1.5 lie
exclusively with the users of HEROS-xtreme helmets.
WARNING: In the case of non-adherence to these stipulations,
Rosenbauer cannot give any guarantees concerning the perfect function
of the HEROS-xtreme fire fighting helmet! Rosenbauer's conditions of
liability and warranty are not extended due to this information.
1.7 The HEROS-xtreme fire fighting helmet was developed in accordance with
the relevant standards, but does not come with a guarantee that injury can be
excluded.
WARNING: In the case of exceptional loads, the helmet absorbs
energy, which can lead to damage and subsequently to negative effects
on the protective function. Such damage may not be immediately
evident and therefore, every helmet that has been subjected to such
heavy loads should be taken out of operation immediately!
WARNING: Should another item of personal protection equipment or an
accessory (except for those accessories provided by the manufacturer
for use with this helmet) be mounted onto a helmet designated as being
in accordance with EN 443, this may possibly cease to fulfil every
section of the standard.
User Guide HEROS-xtreme - Rosenbauer
GB
25 25