Product Description And Specifications; Safety Warnings For Sander; Intended Use; Product Features - Berner BROS-125 AVE Manual Original

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.

Safety Warnings for Sander

Only use the power tool for dry sanding. Wa-
u
ter entering a power tool will increase the risk
of electric shock.
Ensure that no persons are at risk due to fly-
u
ing sparks. Remove combustible materials
from the surrounding area. Flying sparks are
created when sanding metals.
Warning: Danger of fire! Avoid overheating
u
the workpiece and the sander. Always empty
the dust collector before taking a break from
work. Sanding dust in the dust bag, microfilter,
paper bag (or in the filter bag or vacuum
cleaner filter) can spontaneously combust un-
der certain conditions, for example if flying
sparks are created when sanding metals. This
risk is increased if the sanding dust is mixed
with paint or polyurethane residue or with other
chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regu-
u
larly. The motor's fan will draw the dust inside
1 609 92A 4DE • 14.1.19
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
Hold the power tool firmly with both hands
u
and make sure you have a stable footing. The
power tool can be more securely guided with
both hands.
Always wait until the power tool has come to
u
a complete stop before placing it down.
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A ap-
proved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in
its place by an authorised customer service agent.
The replacement plug should have the same fuse
rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be inser-
ted into a mains socket elsewhere.
Product Description and
Specifications
Please observe the illustrations at the beginning
of this operating manual.

Intended Use

English
The power tool is intended for dry sanding of
wood, plastic, metal, filler and varnished surfaces.
Power tools with electronic control are also suit-
able for polishing.
This power tool is not suitable for bench-mounted
use.

Product Features

The numbering of the product features refers to
the diagram of the power tool on the graphics
page.
(1) Auxiliary handle
(2) Screw for auxiliary handle
(3) Orbital stroke rate preselection thumbwheel
(4) On/off switch
(5) Lock-on button for on/off switch
(6) Filter element (filter system for fine dust)
English
Read all the safety and general in-
structions. Failure to observe the
safety and general instructions may
result in electric shock, fire and/or ser-
ious injury.
English
English
English | 13