Install Pdc Control Unit; Coding; Wiring Diagram - BMW 419643 Instrucciones De Montaje

F 39 66 011 M
Install branch cable B5 to installation location of
the PDC control unit.
Install branch cable B2, cable colour violet/black,
to fuse holder A49 (1) above the battery and press
in at output of fuse F61, X10018, connection 12.
Install branch cables B3 and B4 along the vehicle
wiring harness to the right rear light.
Connect branch cable B4, cable colour
brown/black, to ground post X13075 (2) under the
rear light on the right.
only vehicles without power supply for fuse F61.
Cut cable of cable colour violet/white at the output
of the load-reduction relay K3 (3) term. R. Remove
insulation and crimp on to each lead-end a contact
socket, put on socket housing and connect to
connections C1, cable colour violet/white.
Press branch cable C2, cable colour violet/white,
in at input of fuse F61, X10018, connection 11.
Protect with 5A fuse.
F 39 66 012 M
Install branch cable B3 along the vehicle wiring
harness to the plug-in connector X322 (1) behind
the left boot trim-panel.
Connect branch cable B3, cable colour
white/grey/yellow, to connection 4 of the plug-in
connector X322 (1).

8. Install PDC control unit

F 39 66 013 M
Fasten PDC control unit A81 (1), as illustrated, to
the bracket (2) with the plastic nuts (3).
F 39 66 014 M
Put on speed nut (1) and undo plastic nuts (2).
F 39 66 015 M
Insert PDC control unit A81 (1) with bracket as
illustrated and fasten it with washer assembly (3)
and plastic nuts (2).
Insert the plug-in connectors A5 and B5 in the
identical colour mating connectors of the PDC
control unit A81 (1) and arrest in position with the
locking clamps.
Reassemble the vehicle in the reverse order of
disassembly.

9. Coding

Coding of the PDC control unit is necessary in
order to provide optimal conformity of the PDC
retrofit system to the vehicle-specific conditions.
For coding the PDC control unit, the Mobile
Diagnostic Computer MoDiC (III) or the DIS with
CD version 16 (or higher) is required. Coding with
an older version is not possible.
The following sets out briefly the step-by-step
procedure for coding:
Connect MoDiC (III) or DIS to the diagnostic plug in
the vehicle and switch on the ignition.
Select menu item "Coding/Programme"
"Coding ZCS"
"Coding via central coding key (ZCS)
Version 16.0" (or higher)
Select "Series E 39"
"Retrofit"
"PDC"
"automatic coding"
Note
When coding is terminated, switch off ignition for
approx. 10 seconds. Then carry out function test.

10. Wiring diagram

F 39 0121 EVA
A49 Fuse holder IV
A81 PDC control unit
B34 Ultrasonic sensor rear left
B35 Ultrasonic sensor rear centre left
B36 Ultrasonic sensor rear centre right
B37 Ultrasonic sensor rear right
H40 PDC speaker
X300 12-pole black connector
X322 Kar-Radio/HiFi
X362 2-pole black connector
X6500 Plug-in connector adapter
X6501 Connection adapter lead
X10018 Fuse strip IV A49
X13075 Ground
X18013 12-pole white connector
X18020 3-pole black connector
X18021 3-pole black connector
X18022 3-pole black connector
X18023 3-pole black connector
<Enter>
<Enter>
<Enter>
<Enter>
<Enter>
<Yes>
EN/11