Eldom twist OB20B Manual De Instrucciones página 11

ASSEMBLY
- Unpack the product and check all components for damage.
Open the dust canister lid (14) and place the HEPA filter (16a) first and the intake filter (16b) second in the dust canister (15),
-
see Fig. 1. Secure both filters by turning them clockwise to stop. Then, close the dust canister lid (13).
NOTE. Do not use the vacuum cleaner without the filters (16a, 16b) installed.
Press the brush tool shaft release (21), install the brush tool shaft (20) in place and secure it with the release (21), see Fig. 2.
-
NOTE. Do not use the vacuum cleaner with the brush tool (9) without a correctly installed brush tool shaft (20).
- Insert the assembled brush tool (9) in the brush tool adapter (11) or the wand adapter (6), see Fig. 2. To remove the brush tool,
press the brush tool release (12) or the wand release (5) and slide it out of the adapter.
Insert one end of the wand (7) into the wand adapter (6).
-
- The crevice tool (24) can be attached to the brush tool adapter (11) or the wand adapter (6) as required.
The vacuum cleaner starts working when you press the power switch (1). The suction power can be adjusted with the suction
-
power control (2).
- Observe the filling level of the dust canister (15). When the dust canister is filled to the MAX line, empty the dust canister (15)
(see Section EMPTYING THE DUST CANISTER).
NOTE. Do not start the vacuum cleaner if the dust canister contents reach the MAX line.
- The brush tool shaft (20) in the brush tool (9) rotates at a very high speed. Do not let the brush tool (9) dwell too long at the
same place to avoid damage to the flooring.
NOTE. The motorized brush tool (9) has an overheating protection that can cut off the power supply from the brush tool
shaft drive (20) if the shaft drive is blocked. If this happens, turn off the vacuum cleaner, remove the brush tool shaft and
clean it. Do not turn on the vacuum cleaner until it cools down.
Press the power switch (1) to stop the vacuum cleaner.
-
NOTE. Do not obstruct the air outlet vents in the vacuum housing (4) when the vacuum cleaner is running.
CLEANING AND MAINTENANCE
- Before carrying out any maintenance or repair work, turn off the vacuum cleaner and disconnect it from the power supply.
Regular cleaning and replacement of the filters (16a, 16b) and emptying the dust canister (15) will ensure failure-free
-
operation of the vacuum cleaner.
- Clean the vacuum housing, the tools and accessories and the power cord with a soft cloth slightly damp with water and a little
of dishwashing soap.
- Do not immerse the vacuum cleaner in water.
- Do not use any aggressive cleaning agents to clean the vacuum housing, otherwise its surfaces can be damaged.
Emptying the dust canister
Regular emptying of the dust canister ensures proper operation of the vacuum cleaner and helps maintain the optimum suction
power.
- Make sure that the vacuum cleaner is turned off.
Open the lid (14) of the dust canister (15) above a trash bin and dispose of the dust and debris.
-
- Then remove the filters (16b and 16b) from the dust canister held over the trash bin and clean the filters.
The intake filter (16b) can be washed with water and needs to be dried thoroughly afterwards.
-
- Do not wash the HEPA filter (16a) with water every time you clean it. Clean it with water if the dirt is very persistent. Having
cleaned it with water, dry the HEPA filter thoroughly (leave it to dry for at least 24 hours) before using it again.
- Wipe the inside of the dust canister clean with a damp cloth.
NOTE. The filters (16b, 16a) must be thoroughly dried and installed in the dust canister (15) before using the vacuum
cleaner again.
Filters
Check the condition of the filters (16a, 16b) regularly and replace them periodically. This applies especially to the HEPA filter (16a).
NOTE. Filters are consumables and subject to natural wear and tear, and therefore cannot be replaced under warranty.
Cleaning the motorized brush tool (9)
- Make sure that the vacuum cleaner is turned off.
- Press the release (12 or 5) and remove the brush tool (9).
Press the release (21) and push out the brush tool shaft (20), see Fig. 2. Clean the brush tool shaft. It is best to use scissors to
-
cut the hair entangled in the brush tool shaft.
- Clean the brush tool (9) with a soft cloth slightly damp with water and a little of dishwashing soap.
EN 11