Milwaukee HEAVY DUTY M18 ONEFHIWF1D Manual Del Usuario página 19

Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries
to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
WARNING This device contains a lithium button/coin cell
battery. A new or used battery can cause severe internal burns and
lead to death in as little as 2 hours if swal lowed or enters the body.
Always secure the battery cover. If it does not close securely, stop
using the device, remove the batteries, and keep it away from
children. If you think batteries may have been swallowed or
entered the body, seek immediate medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or allow a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and loosen
nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions
of the directives 2011/65/EU (RoHS), 2006/42/EC, 2014/53/EU
and the following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 62479:2010
EN 301 489-1 V2.2.3 (2019-11)
EN 301 489-17V3.1.1(2017-02)
EN 300 328 V2.2.2(2019-07)
EN IEC 63000:2018
Winnenden, 2019-12-15
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
OPERATION
Note: It is recommended after fastening to always check the
torque with a torque wrench.
The fastening torque is aff ected by a wide variety of factors
including the following.
• State of battery charge – When the battery is discharged voltage
will drop and the fastening torque will be reduced.
• Operation at speeds – Operating the tool at low speeds will
cause a reduction in fastening torques.
470 343 - M18ONEFHIWF1D, M18 ONEFHIWF1DS.indd 19 470 343 - M18ONEFHIWF1D, M18 ONEFHIWF1DS.indd 19
• Fastening position – Holding the tool or the driving fastener in
various angles will aff ect the torque.
• Drive accessory/socket – Failure to use the correct size
accessory or socket, or a non-impact rated accessory may cause
a reduction in the fastening torque.
• Use of accessories and extensions – Depending on the
accessory or extension fi tment can reduce the fastening force of
the impact wrench.
• Bolt/Nut – Fastening torques may diff er according to the
diameter of the nut or bolt, the class of nut/bolt and the length of
nut/bolt.
• Condition of the fastener – Contaminated, corroded, dry or
lubricated fasteners may vary the fastening torques.
• Condition and base material – The base material of the fastener
and any component in between the surfaces may eff ect the
fastening torque (dry or lubricated base, soft or hard base, disc,
seal or washer between fastener and base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it will
become.
To help prevent damaging the fasteners or workpieces, avoid
excessive impacting.
Be particularly careful when impacting smaller fasteners because
they require less impacting to reach optimum torque.
Practice with various fasteners, noting the length of time required
to reach the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the head of
the fastener aff ects the degree of tightness.
The torque required to loosen a fastener averages 75% to 80% of
the tightening torque, depending on the condition of the contacting
surfaces.
On light gasket jobs, run each fastener down to a relatively light
torque and use a hand torque wrench for fi nal tightening.
DRIVE CONTROL
The drive control button is used to adjust the torque, rotation speed
(RPM), and impact speed (IPM) for the application.
To select the drive control mode:
1. Pull and release the trigger to turn on the tool. The current mode
indicator is lit.
2. Press the drive control button
Select wireless to change the default settings via the
ONE-KEY™ App on your smart device. When the desired mode
indicator is lit, begin work.
NOTE: Select the torque range in accordance with the equipment
manufacturers fastening instructions.
For precision applications, confi rm the fi nal tightening torque with a
calibrated device.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please
reference the Quick Start guide included with this product or go to
www.milwaukeetool.com/one-key. To download the ONE-KEY app,
visit the App Store or Google Play from your smart device.
When the product experiences ESD, the speed LED shuts down
and the product cannot adjust speed. It needs the battery and coin
cell removed and reinserted to recover (see page 6 & 15).
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset manually
to recover.
We considered the results to be within our minimum acceptable
performance level according to EN 55014-2 / EN 301489-1 / EN
301489-17.
to cycle through the modes.
ENGLISH 19
07.07.2020 09:40:58 07.07.2020 09:40:58