Style selections LWS24BDVJ Manual De Instrucciones página 3

ASSEMBLY INSTRUCTIONS
Step 4: Adjustable Shelf Installation
Note: The adjustable shelf is pre-installed for shipping. If the shelf
position is not to your liking, you will need to reposition the shelf by
following the steps below:
4.1. Look under the shelf, and locate the wood screws holding the shelf to
the shelf supports.
4.2. Remove the wood screws from each shelf support with a Phillips
screwdriver (not included).
4.3. Remove the adjustable shelf from the vanity (B).
4.4. Remove the shelf supports from the vanity (B) and re-position them
in the desired location. Make sure you place the shelf supports in the
same level so the shelf is not tilted.
4.5. Place the adjustable shelf back onto the shelf supports.
4.6. Using the Phillips screwdriver, reinstall the wood screws through the
shelf supports and into the shelf.
Step 5: Sliding Door Set Installation
5.1. Hang the sliding door set (D) onto vanity (B) by putting the pulleys
(preassembled) on the upper iron bar of vanity (B). Then, insert the
lower iron bar of vanity (B) into the groove on the bottom of the door.
5.2. To keep the door from coming off of the track, loosen bolt on "L"
bracket and move up to 1/8 inch from metal bar, Then re-tighten.
4
B
5
Bolt
B
L-bracket
D
B
4
ASSEMBLY INSTRUCTIONS
Step 6: Backsplash Installation
6. To mount the backsplash (C) to the wall, apply a thin bead of silicone
compound (not included) to the unpolished back side and bottom of the
backsplash (C). Position backsplash (C) as shown onto vanity top (A)
and against the wall. Clean any excess silicone compound before
allowing to dry.
Step 7: Vanity Drawer Removal
Removing the Drawer:
7.1. Unload the contents from the drawer.
7.2. Slide out the drawer as far as it will go.
7.3. Press the lever down on the right-hand track and lift the lever up on the
D
left track to release the drawer. Pull the drawer out the rest of the way.
Replacing the Drawer:
7.1. Align the drawer guides with the receiving glides.
7.2. Hold the receiving glides firmly and insert the drawer guide.
NOTE: It is normal for the drawer to close tightly the first time after it has
been removed.
7.3. Push the drawer in completely.
CARE AND MAINTENANCE
• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner. Make sure to dry the wood immediately with a soft
A
cloth or towel.
• The engineer top can be cleaned using standard engineer cleaning agents (sold separately).
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch; for worn areas, stroke in direction of wood grain.
Rub excess colorant promptly with a soft cloth.
B
• Keep product away from direct sunlight as it may damage the finish.
• Be sure to immediately clean red wine or coke stains within 30 minutes or the top will stain.
D
ONE-YEAR LIMITED WARRANTY
This product is warranted to the original purchaser. If there is a failure in this unit due to defects in materials or workmanship,
the manufacturer will repair or replace this item at our discretion without charge. Warranty is void if product has been assembled
incorrectly, misused, abused by overloading, altered in any way or damaged due to accident. This warranty is not transferable
and does not cover chipping, flaking, scratches, rust, dents, or other damages to the surfaces of this product. Responsibility
of the manufacturer is limited to repair or replacement of this product. The manufacturer is not responsible for consequential,
incidental, or other damages or losses resulting from product failure.
This warranty is in lieu of all other expressed warranties. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may
have other rights which vary from state to state.
6
C
7
B
5
Silicone
A