Publicidad
Idiomas disponibles
Idiomas disponibles
Safety Instructions:
Ø Before installation read these instructions carefully and
completely. This installation instruction cannot account
for every possible condition of installation, operation or
maintenance. Further information can be obtained from
your local distributor's office or from the product
datasheet, which can be downloaded, from the Internet
at http://www.automationdirect.com.
Ø The power supplies are constructed in accordance with
the safety requirements of IEC/EN60950, UL60950 and
UL508 . They are approved (BG-mark) in accordance
with EN60950, EN50178, EN61558-2-8 and fulfill the
requirements of the Low Voltage Directive (LVD). They
are UL and cUL approved in accordance to UL60950
(recognised) and UL508 (listed).
Ø Before any installation, maintenance or modification
work ensure that the main switch is switched off and
prevented from being switched on again.
Non-observance, touching of any live components or
improper handling of this power supply can result in
death, severe personal injury or substantial property
damage. Proper and safe operation is dependent on
proper storage, handling, installation and operation.
Ø Compliance with the relevant national regulations (in
the USA, Europe and other countries) must be ensured.
Before operation is started the following condi t ions must
be ensured:
v Connection to mains supply in compliance with
national regulations (VDE0100 and EN50178).
v By use of stranded wires, all strands must be
fastened in the terminal blocks.
v Power supply and mains cables must be sufficiently
fused.
v Degree of protection I to IEC536. The non-fused
protective earth connection must be connected to
the FG terminal (Protection Class I).
v All output wires must be rated for the power supply
output current and must be connected with the
correct polarity.
v Sufficient cooling must be ensured.
Ø Never work on the power supply if power is
supplied! Risk of electric arcs and electrical shock,
which can cause death, severe personal injury or
substantial property damage.
Ø Warning: Hazardous voltages and components storing
a very substantial amount of energy are present in this
power supply during normal operating conditions.
However, these are inaccessible. Improper handling
may result in an electric shock or serious burns! Do not
open the power supply until at least 5 minutes after
it has been disconnected from the mains on all
poles.
v Only trained personnel may open the power supply.
v Do not introduce any objects into the power supply.
The output voltage adjustment potentiometer may
only be actuated using an insulated screwdriver.
v Keep away from fire and water
http:// www.automationdirect.com
Installation Instructions:
Ø This power supply is designed for professional indoor
systems. In operation the power supply must not be
accessible. It may be installed and put into service by
qualified personnel only.
Ø Do not operate without PE connection! To comply with
EMC and safety standards (CE mark, approvals) the
power supply must be operated only if PE terminal is
connected to the non-fused earth conductor.
Ø The correct mounting position for optimal cooling
performance must be observed. Do not cover any
ventilation holes. Observe free space requirements
and power derating as specified on the front of this
sheet.
Ø The internal fuse is not accessible. It is not to be
replaced by the user. If this internal fuse has blown, the
power supply has an internal defect and, for safety
reasons, must be shipped to the local distributor. In
case this internal fuse has to be replaced in the field,
replace only with same type and rating of fuse for
continued protection against ri s k of fire.
Ø Recycling: The unit contains elements that are suitable
for recycling, and components that need special
disposal. You are therefore requested to make sure that
the power supply will be recycled at the end of its
service life.
Ø WARNING: To minimize the risk of potential safety
problems, follow all applicable local and national codes
that regulate the installation and operation of your
equipment. These codes vary from area to area and it is
your responsibility to determine which codes should be
followed, and to verify that the equipment, installation,
and operation are in compliance with the latest revision
of these codes.
v Equipment damage or serious injury to personnel
can result from the failure to follow all applicable
codes and standards. We do not guarantee the
products described in this publication are suitable
for your particular application, nor do we assume
any responsibility for your product design,
installation, or operation.
v If you have any questions concerning the installation
or operation of this equipment, or if you need
additional information, please call us at
770-844-4200.
v This publication is based on information that was
available at the time it was printed. At
Automationdirect.com™, we constantly strive to
improve our products and services, so we reserve
the right to make changes to the products and/or
publications at any time without notice and without
any obligation. This publication may also discuss
features that may not be available in certain
revisions of the product.
Rev: 09/03
Publicidad
