Raider RD-DH02 Manual Del Usuario página 9

1. General guidelines for safe operation.
Read all instructions carefully. Failure of the nature following instructions can cause electric shock, fire
and / or severe injuries. Keep these instructions in a safe place.
1.1. Work area safety.
1.1.1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
1.1.2. Do not operate in an environment where the hammer drill with an increased risk of an explosion
in the vicinity of flammable liquids, gases or powders. During operation of the hammer drill can be
separated sparks that can ignite powders or fumes.
1.1.3. Keep children and bystanders at a safe distance while working with the hammer drill.
If your attention is diverted, you may lose control over the hammer drill.
1.2. Electrical safety.
1.2.1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce
risk of electric shock.
1.2.2. Avoid touching your body to earthed bodies, e.g. pipes, heaters, stoves and refrigerators. When
your body is grounded, risk of electric shock is greater. Protect your striking drill from rain and moisture.
Penetration of water into the hammer drill increases the risk of electric shock.
1.2.3. Do not use a power cord for the purposes for which it is not provided, e.g. to bear the hammer
drill for cable or removing the plug from the outlet. Protect cords from heat, oil, and contact with sharp
edges or points of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
1.2.4. When you work with the angle grinder out, switch the machine only in installations equipped
with electric switch "Fi" RCD (Residual Current Device). RCD must be no more than 30 mA. When use
of extension cord is necessary always remember to use appropriate one up to 15 m, section 1.5 mm
Extension cord should be unwound whole. Use an extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
1.2.5. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
1.3. Personal safety.
1.3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do not use the
hammer drill, when you are tired or under the influence of drugs, alcohol or narcotic drugs. A moment of
distraction at work striking drill may have the effect of extremely serious injuries.
1.3.2. Work with protective work clothing and always with safety glasses.
Wearing Suitable for drilling shock and the activities of personal protective equipment, such as
respiratory masks, healthy, tightly closed shoes grapple with a stable, protective helmet and silencers
(hearing protectors), reduces the risk of accident.
1.3.3. Avoid the danger of incorporating the hammer drill inadvertently. Before you turn the plug into
the power supply network, make sure the trigger switch is in position "off". If, when you carry the hammer
drill, keep your finger on the trigger switch, or if you submit a voltage of the hammer drill, where it is
included, there is the risk of accident.
1.3.4. Before you turn on the hammer drill, make sure that you have removed all of her utilities and
wrenches. Utilities, forgotten rotating unit can cause injuries.
1.3.5. Avoid unnatural positions of the body. Work in a stable position of the body at any time and keep
the balance. So you can control the hammer drill better and safer if unexpectedsituations arise.
1.3.6. Work with appropriate clothing. Do not operate with loose clothing or ornaments. Keep your
hair, clothes and gloves at a safe distance from rotating units of the hammer drill. Robes, attire, long hair
can be caught and carried away by chuck.
1.3.7. If possible use an external aspiration system, make sure it is switched on and functioning
properly. Use of the aspiration system reduces the risks due to the discharge dust at work.
1.4. Hammer drill use and care.
1.4.1. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
1.4.2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot
9
.
2