Black and Decker XTC18BK Manual De Instrucciones página 6

ENGLISH
Fig. A
11. Charger
12. Charger receptacle
13. Charging indicator
14. End of charge indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (9), line it up with the receptacle on the
N
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (10) while
N
at the same time pulling the battery out of the receptacle.
Fitting the side handle
Loosen the side handle (8) by turning it counterclockwise.
N
Slide the side handle over the chuck and onto the housing.
N
Tighten the side handle by turning it clockwise.
N
Fitting and removing a drill bit or screwdriver bit (fig. C)
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
N
the centre position.
Open the chuck by turning the front part (15) with one
N
hand while holding the rear part (16) with the other.
Insert the bit shaft (17) into the chuck.
N
Firmly tighten the chuck by turning the front part (15) with
N
one hand while holding the rear part (16) with the other.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (7).
To remove the screwdriver bit from the bit holder, lift the
N
bit from the recess.
To store the screwdriver bit, firmly push it into the holder.
N
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. When charging the battery for the first time, or
after prolonged storage, it will only accept an 80% charge.
After several charge and discharge cycles, the battery will
attain full capacity. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
6
XTC24BK - Using the 3 hr charger
To charge the battery (9), remove it from the tool and slide
N
the charger receptacle (12) onto the battery.
Plug in the charger (11).
N
The battery will become warm while charging. After approx.
3 hours of charging, the battery will be sufficiently charged for
use in regular applications. After approx. 6 hours of charging,
the battery will be fully charged.
Remove the charger receptacle from the battery.
N
XTC18BK - Using the 30 min charger
To charge the battery (9), remove it from the tool and
N
insert it into the charger (11). The battery will only fit into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
Plug in the charger.
N
Check if the red charging indicator (13) lights up. If the
N
green end of charge indicator (14) lights up now instead,
the battery is too hot and cannot be charged. If this
happens, remove the battery from the charger, let the
battery cool down for approx. 1 hour and re-insert it.
After approx. 30 minutes of charging, the red charging
indicator (13) will stop lighting and the green end of charge
indicator (14) will light up. The battery is now fully charged.
Remove the battery from the charger.
N
XTC18BK - Checking the battery condition (fig. D)
This tool is fitted with a battery charge indicator, which allows
you to check the condition of the battery.
Press and hold down the button (18).
N
Check to see how many of the lights (19) are on:
N
Battery charge
1 light low
2 lights medium
3 lights high
Selecting the direction of rotation (fig. E)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
N
slider (2) to the left.
To select reverse rotation, push the forward/reverse slider
N
to the right.
To lock the tool, set the forward/reverse slider into the
N
centre position.
Selecting the operating mode or torque (fig. F)
This tool is fitted with a collar to select the operating mode
and to set the torque for tightening screws.