AEG BUS18CBL Manual Original página 19

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
certain industrial chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under
"Technical Data" fulfi lls all the relevant regulations and the directives 2011/65/EU
(RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-11:2016
EN 55014-1:2017
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2019-11-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SPECIFIED CONDITIONS OF USE
This sabre saw cuts wood, plastic, and metal. It can cut straight lines, curves,
and internal cut-outs. It cuts pipes and can cut fl ush to a surface.
Do not use this product in any other way as stated for normal use.
BATTERIES
Battery packs which have not been used for some time should be recharged
before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully charged.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause
high current draw, the tool will stop for about 2 seconds and then the tool will
turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could
become to high. If this happens, the battery will shut down.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the process
has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent
short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
470 331 - BUS18CBL.indd 19
470 331 - BUS18CBL.indd 19
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our AEG service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
machine.
Please read the instructions carefully before starting the machine.
Wear gloves!
Always wear goggles when using the machine.
Accessory - Not included in standard equipment, available as an
accessory.
Do not dispose electric tools, batteries/rechargeable batteries
together with household waste material.
Electric tools and batteries that have reached the end of their life
must be collected separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for recycling advice and
collection point.
n
Stroke rate under no-load
0
V
Volts
Direct current
European Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
19
06.11.2019 10:24:26
06.11.2019 10:24:26

Publicidad

Tabla de contenido
loading

Tabla de contenido