Binding Process - Jamara GERMANY BMW M8 GTE Manual De Instrucciones

GB - Assembly
Attention:
You do not need glue for this kit.
Please attach the stickers at the appropriate place before assembly.
1. Install part B26 and B27 on part 2.
2. Install part C34 and C35 on part C33. After that Install part C33 on part 2.
3. Stick sticker 62 on part B24, sticker 63 on part B32 and sticker 64 on part B23.
Install part B32 on part B30. Install part B24 and B23 as shown in the figure.
4. Install part B30 and B28 on part 2.
5. / 5.1 Stick the sticker 20 and 39 on part C38 and sticker 21 on part C39.
Install part A6 into the front of part 2. After that you Install part D41 and D42 on part A6.
Install part C38 and C39 on the inside of part 1.
6. Insert the two pins at the bottom of D40 (the lower edges of the pins should be smooth)
from the top of part A4. Install parts B22 and B25 on A4.
7. Install part B20 and B21 on part A4. Install the two Assembled parts A4 and 1 together.
8. Install part A5 into A4 as shown in the figure. Install part B18 and B19 on the outside of part 1.
Install B12 and B13 respectively on the left and right sides of 1.
9. Combine the assembled models as shown in the figure. Install part D43 and D44 on part 1.
10. Stick the stickers 69, 70, 71 and 72 on part A7 as shown in the figure. Install part A7 on part 1. Install parts 45 and 46 on part 1.
11. Stick the stickers 48 on part B15 and sticker 49 on part B14. Install part A8 into part C36 as shown in the figure.
Install part B16 into B14, and then insert the installed B14 into the hole of part C36. Install part A9 into C37.
Install part B17 into B15, and then insert the installed B15 into the hole of part C37 as shown in the figure.
12. Insert the upper bone of A8 and A9 into the gap between part 1 and the chassis,Please check if the door can be open and close freely after assembly.
13. Install 2 pieces of 49 respectively on the left and right sides of part 1. Install 4 pieces of 50 respectively on the 4 corners of 1 as shown in the figure.
14. Install part 52 and 53 on the position marked on part 3.
15. Install front and rear wheels as shown in the figure.(when installing the front and rear wheels, please align the inside of the tire with the belt buckle,
do not squeeze it)
16. Connect part 52 and 54 and fix them on the model as shown in the illustration.
Attach part 60 to the model. Connect the cables as shown in the illustration.
17. Install part 56 and 57 on part 3 as shown in the figure.
18. Install part 55 on part 3 as shown in the figure, pay attention to the length of electric wires. The short end to the left and the long end to the right.
19. Please press the wires into the gap. Connect the cables according to color and shape.
20. Combine the assembled models as shown in the figure.
21. Install part 58 on part 3 and put part B31 in part 3. Put 3 pieces of 1.5V "AA" batteries into the car and close the battery cover B29.
You can close the battery compartment by turning part B31 (lock).

Binding process:

Turn on the model. The light on the model flashes. Insert 2 AA batteries into the transmitter, the LED on the transmitter will flash.
When the LEDs on both the model and the transmitter stop flashing, they are bound.
Attention!
● Never operate your model beyond sight. Both the maximum visibility as well as the max. range of your model will depend on many factors such as
weather, location and interfering frequencies. Therefore, before each use perform a range test with a second person securely holding the model and
also check how the model reacts if there is a signal failure e.g. when empty transmitter batteries are installed.
11