Residual Risk; Product Service - YATO YT-85200 Manual Del Usuario

GB

Residual risk

Even when all safety precautions are observed at work, there is still a potential risk of injury. Due to the product structure, the
following risks remain.
Injuries associated with vibrations caused by the device being operated for too long, work in an inappropriate way or with a poorly
maintained device.
Injuries caused by an unexpected hit from hidden, thrown items.

PRODUCT SERVICE

Preparation for operation
The product should be unpacked from its packaging and all packaging elements should be removed. It is recommended to keep
the packaging, which may be useful for transporting or storing the product.
Check whether any part of the product has been damaged during transport, any damage observed, e.g. cracks or deformations,
disqualify the product from further use until damaged parts are repaired or replaced.
It is recommended to place all parts on a fl at, hard and clean ground.
During assembly you should apply the personal protection equipment, such as protective gloves, eye shield, and protective suit.
Attention! Before installing the mower, make sure that the mower has not been connected to the power supply. The
power cable must be disconnected from the mower switch.
the lower part of the handle bracket should be inserted into the hole near the rear wheel and secured with the screws (II). Repeat
these operations on the other side of the mower housing (III). Adjust the upper part of the handle bracket to the lower parts and
connect with screws and knobs (IV). The knobs should be directed to the outside of the handle bracket (V).
the switch housing should be inserted into the rail located on the right side of the handle (VI). The button for releasing the switch
lock should be pointed upwards.
Fasten the switch cable to the handle bracket with a clamp (VII). The position of the bracket should be adjusted that the cable
will not be strained, but at the same time it will not protrude too much from the bracket. A cable that is too protrusive can catch an
obstacle (eg a bush) during operation, which may be the cause of its damage and constitute a risk of electric shock.
You should attach the grass basket hooks to the holes in the top of the basket and make sure that the latches fastened the handle
to the basket wall are fi xed properly (VIII).
Turn over the top cover and fi x the frame of the fl exible part of the basket (IX) with screws and washers. The fl exible part of the
basket should be attached to the frame and the top wall of the basket. The front edge of the elastic part has clamps, which should
be put on the frame (X). The upper edge of the elastic part has stiff ening and latches, which should be fi xed in the holes of the
upper wall of the basket (X).
Grab the basket by the handle and lift it, checking the correctness of assembly (XI).
Mount the grass basket to the mower housing. Raise the cover of the outlet opening, hold the lid in its maximum upper position
and mount the basket on the hooks on the back wall of the mower housing (XII). Leave the lid so that it covers the hole in the
upper wall of the basket (XIII).
Disassembly of the basket can be carried out in reverse order.
The mower with the mounted basket is ready for operation.
Setting the cutting height
The mower allows you to change the cutting height. To do this, you should change the position of the wheel axle in the guides.
Remove the basket, turn the mower the wheels upwards. Pull the axle so that it slides out of the guide socket, change its location
again in the guide socket (XIV). Attention! Make sure, that both sides of each axle and both axles are at the same height.
The springs mounted between the axle and the casing will hold the axles in the sockets.
Place the mower on the wheels and attach the basket.
Warning! If it is necessary to change the height during operation, you should always switch off the mower fi rst, wait for the knife
to stop, disconnect the mower from the power cord and then start working on changing the cutting height. Accidental operation of
the knife during a height setting can result in serious injury.
Connecting the mower to the power supply
The mower is not equipped with a traditional plug attached to the power cable. The plug is rigidly attached to the switch, therefore,
a mower with a mains socket must be connected by using an external cable. Due to the nature of the mower work, you should
always use cables designed for outdoor operation. The power cable should have a single socket that matches the plug in the
mower. It is forbidden to modify the plug or socket to match them. The electrical parameters of the power cable should correspond
to the electrical parameters of the device, which are listed on the nameplate. Please pay attention, that the size of the wires
cross-section area of the power cable depends on the length of the cable. You should observe the following recommendations
regarding the cross-section area of the power cable:
O R I G I N A L I N S T R U C T I O N S
15