Monitor Audio GOLD W12 El Manual Del Propietario página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 68
4. IR (Infrared) Output
For use when controlling other IR devices via the Gold W12. Connect the Gold W12 with a second
device using a mono 3.5mm jack connector and control the second device with its remote via the
Gold W12. This is ideal when the device is out of sight or in another room.
5. Line Level Inputs (Stereo Left & Right)
For connection to a 2 channel/ stereo amplifier system. Connection should be provided by a pair of
high-quality signal cables from the pre-out section of an amplifier.
NOTE: Cable lengths should not exceed 10 metres to avoid interference from other electrical
appliances.
6. RCA Line Level Outputs (Stereo Left & Right)
To be used to feed additional sub-woofers or power amplifiers from the Gold W12 by 'daisy chain'
type connection. The outputs are link-out only connections and do not provide any form of filtering or
amplification. There must be a signal on the stereo input for the linked outputs to work. They can also
be muted from within the application when there is a signal connected.
7. LFE Input (RCA Type)
This input is to be used when connecting the Gold W12 to an AV amplifier/ receiver. When using the
LFE input, the crossover function in the menu/ set-up is not used. This is due to the crossover function
being controlled by the source to which it is connected. Input between LFE and Stereo input is switched
automatically by default but can select between only LFE, only stereo and both in the application.
8. LFE Output/ Link (RCA Type)
To be used to feed additional Gold W12's (or another sub woofer) by 'daisy chain' type connection.
The output is a link out only connection and does not provide any form of filtering. They can also be
muted from within the application when there is a signal connected.
9. Balanced LFE Output (Male XLR Type)
To be used when connecting to the balanced input on an additional sub woofer or amplifier. This is
the best method of connection when using long runs of cables (over 10m, up to 100m). A balanced
connection provides a much better (almost noise free) method of connection over analogue audio type
connectors.
10. Balanced LFE Input (Female XLR Type)
To be used when connecting to the balanced output on the amplifier. This is the best method of
connection when using long runs of cables (over 10m up to 100m). A balanced connection provides a
much better, almost noise free method of connection over analogue audio type connectors.
11. Voltage Selection Switch
Factory preset to suit the voltage of the country of origin. This should not be adjusted.
12. Mains Power Switch
Mains 'rocker switch' providing overall power off and on/ auto. In the on/auto mode, the unit will turn
on when an input signal is sensed or the control dial/ power button on remote is pressed. It will turn
off after 20 minutes (default setting) when the signal is removed (source turned off). Alternatively, using
the 12V trigger (see above) to control the power by turning the source on or off.
13. IEC Mains Power Connector/Fuse Location
The Gold W12 is supplied with a three-pin mains input socket for connection to the mains supply. Use
ONLY the appropriate IEC mains lead provided with the product. Also fitted is an external mains fuse.
If a fuse blows during operation a spare fuse is provided within the fuse holder for replacement. If you
wish to change the fuse, you can do this by removing the IEC mains lead and carefully levering out the
original fuse from its holder below the IEC mains input socket (13a, opposite). If the fuse blows again it
is advisable to seek help from an authorised service agent. DO NOT attempt to re-fit a further fuse as
this could result in serious damage to the amplifier unit.
monitoraudio.com
5

Publicidad

Tabla de contenido
loading

Tabla de contenido