General Maintenance - Krups EA89 Serie Manual Del Usuario

Provides access to cleaning the machine's coffee circuit (using a cleaning tablet), which
Coffee cleaning
ensures the optimum taste of coffee.
Provides access to descaling which is essential for the durability of your machine. When the
Descaling
number of drinks is not high enough for descaling to be necessary, the function is not active.
Provides access to the filter mode, useful if the water is very hard, in order to ensure the best
Filter
taste and the health of your machine.
To quit the Cleaning menu, press or the Settings button.
Info
The "Info" menu provides access to information about your use and about certain stages in the life of your machine. It
also informs you about its upkeep. Below are the main details available.
Drinks prepared
Displays the number of drinks prepared
Coffee circuit cleaning
Indicates that is needs to be completed within x number of cycles.
Descaling Indicates that is needs to be completed within x number of cycles.
Filter Indicates that it will need to be changed in x days or x litres.
To quit the Info menu, press or the Settings button.

GENERAL MAINTENANCE

Emptying the coffee grounds collector and the drip tray
After a certain number of coffees, the machine will ask you to empty the coffee grounds collector and the drip tray. Not
to make correctly these operations can damage your machine.
The drip tray collects used water and the coffee grounds collector collects used ground coffee.
If the message "Please empty the two trays" is displayed, remove, empty and clean the drip collector tray. Remove,
empty and clean the coffee grounds collector (C). Fig. 19.
Replace the coffee grounds collector. Fig. 20
The drip tray is equipped with a float to indicate when it needs emptying. However, the machine is also programmed to
ask for the drip collector tray to be emptied after a certain number of coffees, in addition to any intermediate emptying
operations that you may complete.
Rinsing the circuits:
You can start rinsing at any time by pressing and selecting Maintenance.
According to the type of recipe prepared, the machine may complete an automatic rinsing when it is turned off.
It is also possible to set an automatic rinse program when it is switched on (see "Settings" section p.22).
Automatic cleaning programs
Automatic cleaning program of the coffee circuit
A message on the screen will indicate when a cleaning program needs to be run for the appliance.
To run this cleaning program, you will need a container which holds at least 0.6 l, and which should be placed beneath
the coffee outlets and the steam nozzle, and a KRUPS cleaning tablet. Fig. 37. Carefully follow the instructions given
on the screen. It is also possible to run a cleaning cycle via the Maintenance menu.
!
Important: You do not have to run the cleaning program as soon as the appliance requests it, but it must be
done reasonably soon after. If cleaning is postponed, the alert message will remain illuminated until
the process is completed.
The automatic cleaning program comprises two phases: a cleaning cycle and a rinsing cycle, and lasts about 13
minutes.
28
!
Important: If you unplug your machine during the cleaning cycle, or if there is a power failure, the cleaning program
will continue from the current phase when the power is returned. It is not possible to postpone this
process. This is essential to ensure that the water circuit has been correctly rinsed. In this case, a new
cleaning tablet may be necessary. Complete the full cleaning program in order to remove all of the
cleaning product which is harmful to health.
Cleaning the "One Touch Cappuccino" block
To complete a cleaning program, you will require two containers (minimum 0.6 L) and KRUPS cleaning liquid.
You can start the cleaning cycle by pressing button
Then selecting "Maintenance"  "Milk Cleaning". Follow the instructions on the screen.
Dismantling the "One Touch Cappuccino" block
In addition to rinsing, it is necessary to clean the different elements of the block every time after using. To dismantle
the block, follow the following instructions:
Remove the milk tube, Fig. 21.
Remove the front lid of the coffee milk nozzles. Slide it downwards and pull it towards you. Fig. 22.
Remove the "One Touch Cappuccino" block by pulling the upper part of the block and pull the orange cleaning tool.
Fig. 23.
Completely dismantle the block. Fig. 24.
Remove the milk tube connector Fig. 27.
Clean all of the dismantled parts (block, connector and milk tube) with soapy water. Then rinse them in hot water. Fig.
28.
Once the elements are clean and dry, assemble the block and return them to their original position. Fig. 33.
Replace the font lid of the block. Fig. 34. Replace the connector in the milk tube Fig 35 (opposite side of the bevelled
side) and plug in the block. Fig. 36.
Automatic descaling program of the steam circuit
Warning: if your appliance is fitted with our Claris - Aqua Filter System cartridge, remove the cartridge before
descaling.
A message on the screen will indicate when a descaling program needs to be run for the appliance. The frequency of
this program depends on the quality of the water used and on whether a Claris Aqua Filter System filter is used or not
(the harder the water, the more often the appliance has to be descaled).
!
Important: You are not obliged to carry out this program immediately the appliance requests it, but it must be
carried out reasonably soon afterwards. If descaling is postponed, the alert message will continue to
be displayed until the process is completed.
When the descaling alert level is reached and displayed, press
.
Once the procedure has been launched, follow the instructions provided on the screen. It is also possible to run a
descaling cycle via the "Maintenance" menu  "Descaling".
To carry out a descaling program, you will require a container with a capacity of at least 0.6 L which should be placed
beneath the One Touch Cappuccino block and a KRUPS descaling sachet (40 g). Fig. 37
Fill the water tank up to the CALC mark then pour in the contents of one sachet of descaler.
The descaling program comprises three phases: a descaling cycle and two rinsing cycles. The program lasts
approximately 20 minutes.
!
Important: If there is a power failure or if you unplug your machine, the cycle will continue from the current phase
when the power is returned. It will not be possible to cancel this operation. Complete the full cycle in
order to remove all of the descaling product which is harmful to health.
.
to run the descaling program. To delay it, press
29