Peg-Perego pliko p3 Instrucciones De Uso página 13

LOADS.
• ENSURE THAT THE STROLLER IS
OPENED CORRECTLY AND LOCKED IN
POSITION OF USE.
• CHECK TO MAKE SURE THAT THE
CAR SEAT OR THE BABY CARRIAGE
IS CORRECTLY FASTENED TO THE
STROLLER (WHERE APPLICABLE).
• DO NOT DRIVE THIS PRODUCT
AROUND STAIRS OR STEPS; CARE MUST
BE TAKEN IF UNIT IS USED ON STAIRS
OR ESCALATORS.
• DO NOT USE THE PRODUCT IF IT HAS
BROKEN OR MISSING PARTS.
• DO NOT USE NEAR FIRE OR EXPOSED
FLAME.
• NOTICE: THIS ARTICLE MEETS OR
EXCEEDS ALL REQUIREMENTS
COVERED IN ASTM F833 STANDARD
AND LATEST REVISIONS.
instructions for use
OPENING
1• Before opening the stroller remove the two
protective caps from the hooks as shown in
the figure. Otherwise, the stroller will not open
correctly.
2• To open the stroller, pull up the two levers on
the handles and
3• at the same time, lift the stroller, which will
open automatically. To make sure that the
stroller has been set up correctly, check the two
side hooks (see figure).
ASSEMBLYING THE STROLLER
4• To mount the front wheels, lower Lever A and
slip the wheels onto the axle, as shown in the
figure. Press until the wheels click into place.
5• To assemble the rear wheels fasten the wheels
connected by the break wire, as indicated in
the figure.
6• Carefully distinguish the left wheel from the
right, to fasten the two rear wheels properly.
The left wheel has a rib on the wheel tube
and one on the chassis to guarantee proper
fastening (see figure).
7• Make sure that it is fastened properly, as
indicated in the figure (click).
8• The stroller comes with caps on the armrests.
To attach the front bar, remove the caps first.
(Keep the caps, in case you want to use the
stroller without the front bar). To remove the
caps, press the buttons under the armrests
while pulling the caps off.
9• To attach the front bar, insert the two ends of
the bar into the armrests and press until the bar
clicks into place, as shown in the figure.
10• To mount the basket, slide the slots onto the
front hooks A and the rear hooks B and C.
11• The figure shows the mounted basket.
12• The drink holder can be placed on the left or
right hand side of the stroller, thanks to the
attachment which is already fitted on both
sides. To fit the drink holder, click it on, as in
Figure A. See Figure B for a fitted drink holder.
Do not put hot drinks in the drink-holder.
PLIKO P3 VERSIONS
13• "Classico" Model: comes with a hood.
HOOD
• The hood comes with a zipper, for attaching
the zip-on rain canopy or mosquito netting
(see Accessories Line).
14• To mount the hood, push the fittings down
until they click, as shown in the figure.
15• As shown in the figure, button the hood inside
the armrest and the backrest of the stroller.
16• To stretch out the hood, push the coupling
downward. The hood can be reclined by
following the inclination of the backrest.
17• The hood is supplied with the front border
folded up. It should not be used like this
however. In order to be able to use the hood
correctly, turn the edge up, as in the figure.
18• It is possible to detach the back part of the
fabric by unzipping it and use the hood as a
sun canopy.
19• To reattach the back part of the fabric, proceed
as indicated in the figure.
20• By lowering the stroller backrest, the hood
extends and, thanks to the double zipper, a
window can be created to allow more air to
circulate and see the child when sleeping.
21• To remove the hood, you must unbutton it
from the stroller, loosen the couplings and raise
the tabs of the fasteners, pushing towards the
inside of the stroller.
BRAKE
22• To apply the brakes, push down with one foot
the bars on the rear wheels, as shown in the
figure. To release the brakes, draw the bar up.
Always set the brakes on the stroller when it is
not in motion.
SAFETY BELT
23• A: Make sure that the brace is properly inserted
by pushing as shown in the figure. B: Fasten the
belt as shown in the figure.
24• To unfasten the belt, press on the buckle sides
and pull out the waist strap.
25• The new safety belt is now easier to fasten
thanks to the "snap-open-and-shut" device.
Before fastening the safety belt, attach the
buckle to the backrest by inserting the tab
through the special holder, as shown in the
figure. After fastening the safety belt on your
child, detach it from the backrest to allow the
child more freedom of movement. The buckle