Descargar Imprimir esta página
Waterpik Cascadia CF-200 Manual De Instrucciones
Waterpik Cascadia CF-200 Manual De Instrucciones

Waterpik Cascadia CF-200 Manual De Instrucciones

Cabezal de ducha empapante

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

drenching rain showerhead
Spray Change
Button
Shower
Arm Nut
Collar
Flexible Arm
Spray Change
Button
Bracket
Adapter
5' hose
Instruction Manual
Flow Control
Waterpik
brand showerheads are equipped with an OptiFLOW
®
lator that limits maximum water flow to 2.5 gallons per minute at 80
psi as mandated by U.S. federal law.
In areas with extremely low water pressure, causing
the shower water flow to be unsatisfactory, the
flow regulator may be removed to improve
the water flow in the showerhead.
To remove, unscrew
filter screen by turning
counterclockwise.
Remove regulator
with needle-nose
pliers and replace
Filter Screen
Washer
filter screen.
Flow Regulator
Filter
Screen
Flexible Installation
Your new showerhead will fit a standard 1/2" shower "J" pipe. Do not
attach this product to a plastic shower arm since it may not provide
adequate support.
Tools are not required. Do not use pipe tape or any other sealants
when installing the showerhead. These materials are not necessary
and may cause the nut to loosen prematurely. Hand tightening is
sufficient to secure the shower thread. Make sure the washer is in the
end of the nut.
DATE: 18 May 2010
FILENAME: FN20010910-FAD_Cascadia.indd
FILE TYPE: Adobe InDesign CS4
SIZE FLAT: 8.375" x 8.5"
DIELINE: N/A
NOTES:
1. Remove old showerhead. Clean pipe threads
thoroughly.
2. Tighten the flexible shower arm onto the
"J" pipe by hand, applying force to
the nut closest to the "J" pipe.
Do not use the flexible shower
arm as a handle to tighten this
connection.
3. Attach the showerhead to the
flexible shower arm by hand
tightening the shower arm collar to the
threaded end of the shower head.
Models:
CF-200
CF-201
CF-201C
CF-203C
CF-209C
CF-261
4. Be sure to properly align threads before tightening.
CF-263C
5. Slowly turn on cold water and check for leaks. If leaks occur,
retighten all connections.
6. Do not use excessive force in positioning the showerhead and/or
arm.
7. If the showerhead is not maintaining its position, re-tighten the
showerhead collar and shower arm nut.
Hand-Held Installation
1. Remove old showerhead. Clean pipe threads thoroughly.
regu-
®
2. Slightly loosen swivel collar on bracket.
3. Hand tighten pivot ball to pipe.
4. Hand tighten adaptor to showerhead.
5. Hand tighten hose to adapter and bracket.
6. Place showerhead in bracket.
Nut
Flow Regulator
(black O-ring
faces out)
Operation
To change settings, from
either the full-body spray
or the concentrated power
spray, push the spray
change button at the base
of the showerhead so it
extends to the opposite side
of its current position.
CLIENT: Water Pik, Inc.
DESCRIPTION: Waterpik Cascadia Showerhead Instruction Manual
PREPARED BY: Brian Colon
SIZE FOLDED: 2.8125" x 4.25"
Spray Change Button
Spray Change Button
FORM: 20010910-F AD
FOLDS: Indicated
INK: Black
Troubleshooting Guide
Problem
Solution
No water flow from
a Confirm previous shower washer is not in the
installed shower
j-pipe.
head:
b Confirm the hose is properly installed, try
switching ends.
c Confirm there is only one washer in the pivot ball.
Low water pressure
a Clean shower head in vinegar/water solution.
or missing spray
(See care section).
patterns
b Clean screen and flow regulator.
Leaking at pipe pivot
a Confirm one single washer is seated on top of
ball connection:
the screen.
b Grate bar of soap across the j-pipe threads to act
as a sealant.
Showerhead and/
a Immerse pivot ball and large nut of the bracket in
or bracket stiff to
hot water or use a blow dryer for several minutes
change angle
and then use a towel to loosen the large nut.
For Fixed Mount: install FM shower head to
provide additional leverage to change angle of
spray. (Contact Waterpik for further assistance).
Care and Cleaning
Clean the filter screen at least once a year, or when you notice a drop in
water pressure. To remove, unscrew the nut from the pipe. Remove the
screen by turning it counter-clockwise (pliers may be used) and rinse.
If you remove the flow regulator, be sure you reinstall it with the black
O-ring facing out.
• Cleaning is required when mineral deposits appear on the spray
holes to maintain proper working conditions.
• Clean the flexible nozzles by rubbing with a finger or soft bristled
toothbrush. Clean by soaking in household vinegar.
• Do not clean or rinse any part with harsh chemicals, heavy-duty
cleaners or abrasives. This may damage parts or finish and may void
the warranty.
Limited Lifetime Warranty
Water Pik, Inc. warrants to the original purchaser of this product that it is
free from defects in material and workmanship for as long as the original
purchaser owns this product. Water Pik, Inc. will replace any part of the
product which in our opinion is defective, provided that the product has
not been abused, misused, altered or damaged after purchase. (This
includes damage due to use of tools or harsh chemicals.) In the event
an item has been discontinued we will replace with what we deem to be
the closest product. Water Pik, Inc. is not responsible for labor charges,
installation, or other consequential cost. The responsibility of Water Pik,
Inc. shall not exceed the original purchase price of the product. This
warranty gives you specific legal rights. You may also have other rights
that vary where you reside. Save your receipt as proof of purchase is
required for warranty action.
Have any questions or need assistance?
If in the U.S., call our toll-free
If outside the U.S., write us at:
Customer Assistance Line,
Water Pik, Inc.
1-800-525-2774
1730 East Prospect Road
Fort Collins, CO 80553-0001 USA
www.waterpik.com
Waterpik
®
(stylized) is a trademark of Water Pik, Inc. registered in the EU,
Switzerland, Mexico, Canada, and United States.
Waterpik
is a trademark of Water Pik, Inc. registered in Argentina, Australia,
®
Austria, Canada, China, Czech Republic, Hungary, India, Japan, Poland, Russian
Federation, South Africa, Switzerland, Ukraine, and the United States.
Cascadia
is a trademark of Water Pik, Inc. registered in Australia, Canada, EU,
®
Switzerland and the United States.
Optiflow
®
is a trademark of Water Pik, Inc. registered in Australia, Canada, the EU,
Korea and the United States.
© 2010 Water Pik, Inc.
Water Pik, Inc.
1730 East Prospect Road, Fort Collins, CO 80553-0001 USA
www.waterpik.com
FN 20010910-F AD

Publicidad

loading

Resumen de contenidos para Waterpik Cascadia CF-200

  • Página 1 Arm Nut For Fixed Mount: install FM shower head to Collar provide additional leverage to change angle of spray. (Contact Waterpik for further assistance). Models: Flexible Arm Care and Cleaning CF-200...
  • Página 2 Control de Flujo 1. Quite la boquilla de la ducha vieja. Limpie meticulosamente Water Pik, Inc. le garantiza al comprador original de este producto que el Los cabezales para duchas de marca Waterpik vienen provistos de ® la rosca del tubo.

Este manual también es adecuado para:

Cascadia cf-201Cascadia cf-201cCascadia cf-203cCascadia cf-209cCascadia cf-261Cascadia cf-263c