Serial Numbers - Martinelli MILANO Navicella Manual Del Usuario

with 3 safety belts. The central one can be 3-point or a lap
belt.
We recommend positioning the bassinet unit on the
vehicle's rear seats with the end for the child's head above
the central seat.
1 4• Navicella fitted in a vehicle with a lap belt.
1 5• Navicella fitted in a vehicle with a 3-point belt.
1 6• The Navicella can also be positioned in the centre of a 3-
person rear seat, using the two outer safety belts (fig_a).
It cannot be positioned as in fig_b because it can only
be secured in vehicles using safety belts that come from
opposite sides.
1 7• Position of the Navicella on a 2-person rear seat. The
Navicella can be positioned with the child's feet on either
side of the vehicle. If the seat of the vehicle inclines, towels
can be used to provide a horizontal surface.
1 8• Take the rear seat belt, fold it as shown in the figure
(arrow_a) and insert it in the slot of the car kit's metal
fastener (arrow_b).
1 9• Insert the red lever on the metal fastener of the car kit inside
the folded belt (arrow_c).
Move the metal fastener as near as possible to the seat in
order to enable it to be fastened to the Carrycot (arrow_d).
2 0• Hook the car kit connector to the ring on the Carrycot and
pull firmly on the belt to ensure the Carrycot fits as well as
possible to the seat.
• Repeat the same operations on the other side of the
Carrycot.
2 1• Car Carrycot installed in the car.
2 2• UNFASTENING THE CARRYCOT FROM THE CAR:
press the control button on the connector to loosen the
belts, as shown in the figure. Unhook the fastener of the car
kit connector from the ring on the Carrycot.
IMPORTANT: the car kit can remain fastened to the
seat belts of your car. The car kit fastener can easily be
attached to or removed from the ring on the Carrycot
(point 22).
How to put the child in the Navicella
2 3• 3-POINT SAFETY HARNESS: Slacken the straps by pressing
on the buckle (fig_a) and lengthen them (fig_b).
All manuals and user guides at all-guides.com
2 4• Press the red button (fig_a) and release the straps from the
2 5• Place the child in the Navicella then buckle together the
2 6• The child must be securely fastened in the Navicella. If the
The straps must be as tight as possible to protect the child
2 7• REMOVE THE STRAPS: To remove the straps from the shell
2 8• Put the harness back in its pocket once it has been
Accessories
2 9• ANTI-SUFFOCATION SET: mattress plus cushion. Compatible
30• BASSINET RAIN COVER: practical, foldable bassinet rain
BORSA CAMBIO: satchel with pad for changing baby's
3 1• BASSINET STAND: Practical, compact support base.
Serial numbers
3 2• Information about the production date of Navicella can be
• Product name, production date and serial number (fig_a).
Car Kit:
• Approval label (fig_b).
• Harness production date (fig_c).
This information is required for any complaints.
• This paragraph explains how to interpret the approval label
18
leg divider (fig_b).
straps and the leg divider.
straps are loose, tighten them by pulling on the end.
in the event of an accident. Leave a minimal amount of
play (the width of a finger between the harness and the
child's chest).
of the Navicella, pass the buckles of the leg divider through
the slots under the shell and pull them through (fig_a). To
remove the strap fasteners from under the shell, release
them from the clips and pass them through the slots
(fig_b).
removed.
with our 3-point car kit.
cover in a bag.
diaper. Fastens to the chassis.
found under the base.
How to read the approval label
(the orange one).