Technical Specifications - V2 KIBO-R Instrucciones De Instalación

EU DECLARATION OF CONFORMITY
V2 S.p.A. hereby declare that KIBO-R equipment conforms to the
essential requirements established in directives:
• Low Voltage Directive 2014/35/EU
• Electromagnetic Compatibility Directive 2014/30/EU
• Radio Directive 2014/53/EU
• Directive RoHS-3 2015/863/EU
Racconigi, 01/06/2020
Legal representative, V2 S.p.A.
Sergio Biancheri
PRODUCT DESCRIPTION AND INTENDED USE
KIBO-R is a fixed radio transmitter intended for commanding one
or more automations for sun screens, rolling shutters, shutters, doors,
garage doors, gates of various types and other similar applications.
Any use other than that described is to be considered
improper and prohibited! l
• The digital switch is a transmitter that is activated by entering a
personalised 1 to 8 character combination on the special, back-lit
numerical keypad
• On entering the correct access code, the switch transmits a digital
code by radio.
• They can be programmed with up to 9 different channels

TECHNICAL SPECIFICATIONS

Power supply: 1 x CR2032 lithium battery
Radio frequency: 433,92 / 868,30 MHz
Radio power: < 1mW
Consumption: Max. 15mA - Min. 1μA
Battery lifetime: 2 years (10 operations per day)
Protection degree: IP54
MAINTENANCE
The transmitter does not require any special maintenance. Check it
occasionally for humidity and oxidation, and clean any dust off it.
Replacing the battery
When the battery is run down, the device BEEPs and flashes for 2
seconds. The battery must be replaced.
In this state, it is not possible to program the device.
Remove the keypad from its mount (fig. A, B); unscrew the cover with
a coin and replace the battery with their positive poles (+) uppermost
(fig. 5). Screw the cover back down, taking care not damage the
gasket; then fit the keypad back onto its mount (fig. 6, 7).
SCRAPPING THE PRODUCT
This product is an integral part of the automation and must therefore
be scrapped together with it, in the same way as indicated in the
automation's instruction manual.
Disposing of exhausted battery
Discharged battery contain pollutant substances and therefore must
never be disposed of as normal waste. Dispose of them in observance
of local sorted waste disposal regulations.
INSTALLATION
Ensure that the system is operating correctly prior to fixing the digital
switch:
1. Program the keypad and store a channel on the receiver (read the
receiver instruction manual carefully).
2. Position the keypad (without fixing it in place) and ensure that
when the previously stored code is transmitted, the receiver
activates the corresponding output.
3. If the system is operating correctly, fix the keypad, otherwise,
reduce the distance from the receiver in order for it to operate
correctly.
m
PLEASE NOTE: Avoid installation of the digital radio
switch on metallic surfaces.
KEY FUNCTIONS
The A key
While entering the access code, pressing the A key cancels the
•
operation: The keypad is immediately ready for entering a new
code.
During programming, pressing the A key cancels all operations
•
and activates STAND-BY mode.
• In STAND-BY mode, it is used to identify the operational mode of
the device (see the following section)
The B key
• Activate radio transmission in mode PERSONAL PASS –
MONOSTABLE
The C key
This is used to activate programming mode and navigate through the
various programs.
The 0,1,2,3,4,5,6,7,8,9 keys
• During programming, these are used to select the menus and set
the various codes.
• During normal operation, they are used to enter access codes.
OPERATIONAL MODE
KIBO-R can operate in 4 different modes, depending on the system
with which it is associated.
ROYAL
• compatibility with dip-switch transmitters transmitting a ROYAL
type code at 433.92 MHz
• 4 access codes available
• the access code set activates the radio transmission
• transmission lasts for 2 seconds, and is indicated by LED L1
coming on
• each access code corresponds to a different channel
53200
• compatibility with dip-switch transmitters transmitting a 12-bit
53200 type code at 433.92 MHz
• 4 access codes available
• the access code set activates the radio transmission
• transmission lasts for 2 seconds, and is indicated by LED L1
coming on
• each access code corresponds to a different channel
PERSONAL PASS
• compatibility with all rolling code transmitters transmitting a
PERSONEL PASS type code at 433.92 MHz
• 9 access codes available
• the access code set activates the radio transmission
• transmission lasts for 2 seconds, and is indicated by LED L1
coming on
• each access code corresponds to a different channel
- 9 -