Wood Maintenance - Jacuzzi VIRTUS Uso-Mantenimiento

the hydromassage and suction intakes, using a liquid-suction
pump. It is advisable to empty the pump as well via the appropriate
drain plug.
Model with Jacuzzi® heat pump: fully empty the heat
pump, slackening the fittings connecting to the system; follow
the instructions provided for the hot tub, to suck up any remain-
ing water.
IMPORTANT
In cold climates, where temperatures drop well below
0°C, all residual water should be eliminated from the cir-
cuit.
Connect a pipe to the filter drainage valve to drain the water
inside.
Cover the hot tub to keep it clean.
Model with Jacuzzi® heat pump: leave the fittings loose, so
as to eliminate any condensation.
Before you use the hot tub again, refer to the chapter on op-
erating checks for first start-up.
Model with Jacuzzi® heat pump: before using the heat
pump again, remember to tighten the fittings again.
In areas where temperatures only occasionally drop below
0°C, the hot tub can be left in operation, since it is equipped with
an anti-freeze protection that ensures that a minimum water
temperature is maintained (see chapter "Setting the water tem-
perature", paragraphs "Maintenance of minimum water tempera-
ture" and "Pipe anti-freeze protection ('Smart Winter')").
SYNTHETIC WOOD MAINTENANCE
Synthetic wood panels require little maintenance; use a neutral de-
tergent when cleaning, rinsing with clean water.
CAUTION
Do not use jets of water to clean the panels as they may
penetrate into the hot tub technical compartment and
cause damage to the electrics.
Maintenance of natural wood parts
Some of the Jacuzzi® spa covering panels and accessories are
made of natural wood, treated with advanced products which en-
hance the natural beauty and ensure protection against atmos-
pheric agents.
The panels and accessories first receive a coat of stain, to give the
wood an even shade. Then two coats of synthetic oil are applied,
which give the piece a natural and particularly warm appearance.
Cleaning
Maintenance varies according to the location of the spa and/
or accessories (sheltered from or exposed to the elements).
In any case, you should periodically wash the surfaces with fresh
water and neutral detergent. Then rinse.
Do not use detergents that contain alcohol, scale-removal sub-
stances, ammonia, abrasive products or bleach.
Do not use wax or polish.
Renewal
At least once a year (or less, depending on the conditions the
wood surfaces are exposed to), do the following:
Lightly sand the surface with an abrasive sponge (or sandpa-
per, grain 320). Do not press too hard, especially near protruding
parts (corners and so on).
Remove all dust. Use a soft-bristled brush to apply a layer of
synthetic oil, first crosswise and then along the entire height of
the panel.
Do not work in direct sunlight, nor if the temperature is espe-
cially cold.
If necessary, remove any excess oil using a microfiber cloth.
Let dry for about an hour (at 20°C).
Note: tools can be washed with turpentine for subsequent reuse.
If more extensive restoration is require (for example, if the pro-
tective layer has been damaged in depth), you should thorou-
ghly sand the entre surface all the way down to the bare wood.
Apply a coat of stain if there are marked differences in shades.
Then apply two to three coats of synthetic oil as necessary, fol-
lowing the same method described for the renewal phase.
Note: make sure that, between one coat and the nest, the product
has dried completely. This normally takes 1 to 2 hours at an ambient
temperature of about 20 °C).
For all special maintenance, it is advisable to contact specialized
personnel.
ATTENTION: sanding residue, tools and rags used to apply
the product may self-ignite if exposed to the air. Keep the re-
cipients (immerged in water) in tightly closed metallic contai-
ners and dispose of them immediately. Comply with current
applicable regulations.
25