SLV 1004776 Guia De Inicio Rapido página 2

Dimmable LED Driver with DALI control input and constant output voltage for the operation of LED
(Electronic power supply unit)
Types: 1004776, 1004777
1. Technical Data:
Art.-No.
Rated voltage
Rated current
Power Factor
Shared load operation
Constant output voltage
Secondary current
Open circuit voltage
Open circuit safety
Control input
Dimming range
Dimming technique
Standby power
Protection class
Degree of protection
Short circuit and overload protection
Ambient temperature ta
Case temperature tc-point
Standards
Diameter of wires
Cable
(Terminals)
Bared wire end
2. Installation Instructions
The installation may only be carried out by an electrical specialist in accordance with international and national standards.
When working on electrical systems, protection against electric shock is to be ensured by disconnecting the system.
Install primary and secondary mains intersection-free (RFI protection). Keep the wiring as short as possible.
The maximum output wire length of 2 m must not be exceeded.
Before switching on the supply voltage all LED must be completely wired and connected!
The LED Driver is strictly suited for the use with LED that requires a constant voltage of 24 Vdc. If the output voltage is incorrect, the LEDs and / or the driver can be destroyed. When
connecting the LED, careful attention should be paid to connecting + and - to the right terminals on the LED Driver.
The LED control gear has no secondary reverse polarity protection. LED modules can be destroyed in reverse polarity.
LED Drivers mounted outside of luminaires are to be screwed tightly to the respective surface by their screw holes and careful attention is to be paid to the connecting cables and the
lamp cables being fastened securely in the strain relief.
The ta or tc temperature may not be exceeded for any kind of mounting. The specified minimum distances are guidelines and dependent upon of the used
luminaire or environment (see last page).
The devices do not contain any serviceable components and may not be opened.
The LED Driver cannot be regulated via a phase cut-on or cut-off dimmer!
3. Isolation
The LED Output (SEC) is double insulated to mains. The DALI / TouchDIM input has a basic isolation to mains and a double isolation to LED Output (SEC).
4. Overvoltage
Our LED Drivers are surge-voltage-stable with values above those prescribed by the respective standards. As a protection against high voltage surges, as they occur e.g.
when switching fluorescent lamps and discharge lamps with an inductive ballast, motors (fans, etc.) and other inductive charges, the load circuits for devices of this kind are to
be clearly separated from each other.
5. Short circuit / overload
In case of a short circuit or overload the LED Driver will automatically cut off. It does not have a fuse of the conventional kind. Thus the load circuit is not separated! As soon as the
defect has been repaired, the LED Driver will automatically cut back in.
7. Excess Temperature
In case of excess temperature through external heat sources or impermissible covers the function will be interrupted. The mains will not be disconnected. As soon as the LED Driver
has cooled off, it will automatically cut back in.
7. Heat Dissipation and Heat Transfer
Operation in excess ambient temperature or through external heating will reduce the service life. During the installation process (particularly into luminaires), heat dissipation
(heat transfer) is to be provided through suitable measures. The ambient temperature and/or tc temperature may not be exceeded at any time. We are not liable for damage
resulting from improper use.
Art.-No. 1004776, 1004777
© SLV GmbH
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany
Tel. +49 (0)2451 4833-0
Technical properties subject to modification.
Description and Mounting Instructions
LADV100W24-Z
4.16 A max.
-20 °C – +50 °C
PRI, SEC
DALI
PRI, SEC
DALI
05/2021
1004776
220–240 V 50–60 Hz
500 mA
0.95
5–100 W
24 Vdc SELV
25 V max.
guaranteed
DALI-2 / TouchDIM
1–100 %
PWM, 2 kHz
< 0.5 W
II
IP20
electronic disconnection with automatic restart
max. 90 °C
EN 61347, EN 62384, EN 62493
EN 61547, EN 55015, EN 61000-3-2, EN 61000-3-3
EN 62386-101, EN 62386-102, EN 62386-207
0.75–2.5 mm²
AWG 18–14
9 mm
1004777
LADV200W24-Z
950 mA
5–200 W
8.33 A max.
-20 °C – +45 °C