Care And Cleaning; Troubleshooting - Homewerks H13L-421-CH Instrucciones De Instalación

INSTALLATION INSTRUCTIONS (CONTINUED)
9. Attach each of the remaining ends
of the water supply lines (9.1) to the
hot and cold water shut-off valves
(9.2) and tighten with a wrench.
Do not overtighten.
OPERATING INSTRUCTIONS
The lever handles control the flow of hot and cold water to the faucet. Moving the handle forward opens the cartridge and causes water
to flow from the spout. Rotate the handle on the right side of the faucet forward for cold water. Rotate the handle on the left side of the
faucet forward for hot water. The degree of handle opening determines the volume of water flow. Returning the handle to the original
position away from the spout on the faucet body stops the flow of water.

CARE AND CLEANING

Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your
warranty.

TROUBLESHOOTING

If a faucet installation doesn't deliver water properly or leaks, finding the cause and fixing it can be easy.
PROBLEM POSSIBLE CAUSE
Faucet leaks Bonnet has come loose or the
underneath handle. ceramic cartridge seal is dirty or
out of place.
Water does not Ceramic cartridge discs are
completely shut off. worn or have debris trapped
inside.
Faucet leaks around The aerator is incorrectly fitted,
aerator. dirty, or small parts inside the
aerator are improperly installed.
Faucet has an improper The aerator is dirty or small parts
water pattern. inside the aerator are improperly
installed.
No water pressure or The connector is blocked.
low water pressure after
a longer period of use.
Homewerks.com
9
9.1
9.2
SOLUTION
1. Move the handle to the OFF position. Unscrew the handle screw and remove the
handle.
2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON position.
The leak should stop draining out from around the cartridge stem.
3. If the leak does not stop, shut off the water supply. Remove the bonnet by turning it
counterclockwise. Lift out the ceramic cartridge. Inspect the seal on the bottom of the
ceramic cartridge. Remove any debris from the seal. If the ceramic cartridge seal is
twisted or out of place, re-seat it. If the ceramic cartridge seal is worn or damaged,
replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on the two sides
of the cartridge bonnet fit into the grooves on the two sides of the faucet body. Tightly
screw the bonnet onto the faucet body.
5. Reinstall the handle.
1. Shut off the water supply.
2. Move the handle to the OFF position. Unscrew the handle screw and remove the
handle.
3. Remove the bonnet. Lift out the ceramic cartridge.
4. Position the new ceramic cartridge into the faucet body.
5. Tightly screw the bonnet into the faucet body.
6. Reinstall the handle.
1. Remove the aerator from the spout on the faucet body. Inspect the black rubber gasket
inside the aerator. The rubber gasket should be flat.
2. Reinstall the aerator on the spout.
1. Remove the aerator from the spout on the faucet body.
2. Gently flush the small parts inside the aerator to clear away any debris.
3. Reinstall the aerator on the spout.
1. Remove the spray head by unscrewing it from the hose assembly.
2. Hold the end of the hose assembly down into the sink and turn the faucet on to the
warm position where it mixes the hot and cold water. If the water flow is still slow or
completely blocked, please call customer service.
10. Once the installation is complete,
remove the spray head (10.1) from
the spout (10.2) on the faucet body
(A) to flush the water lines. Turn
on the water supply and allow both
hot and cold water to run for at
least one minute to flush away any
debris that could cause damage to
internal parts. While the water is
running, check for leaks. If a leak
occurs, gently tighten the nut on
the connection that is leaking. Fill
the sink with water to check the
drain for leaks. If water is leaking
from the drain, tighten the nut on
the drain assembly and empty
the sink. Turn off the water and
screw the spray head (10.1) back
onto the spout (10.2) of the faucet
body (A).
3
10
10.2
10.1
A