Description Of The Parts; Product Features - Chicco NEPTUNE - 2 Instrucciones De Uso

• Cleaning and maintenance

DESCRIPTION OF THE PARTS

diag. 1 (Front)
A. Adjustment knob for the headrest and restraint
harness
B. Headrest
C. Diagonal belt routing slots
D. Shoulder straps
E. Child car seat restraint harness
F. Buckle
G. Crotch protection strap
H. Restraint harness adjustment button
I. Restraint harness adjustment strap
diag. 2 (Profi le)
J. Backrest
K. Seat
L. Armrests
M. Belt routing
diag. 3 (Back)
N. Plates for locking the shoulder straps and for the
belt routing
O. Harness straps
P. Slots for inserting the car seat belts (only for installation
in Gr. 1)
Q. Plate for locking the belts
diag. 4 (Below)
R. Plates for locking the belts to the seat
S. Plates for locking the buckle to the seat
T. Lever to remove the backrest from the seat

PRODUCT FEATURES

• This child car seat is approved for "Group 1, 2 and
3", for the transport of children from 9 up to 36 Kg
of weight (from 9 months to approximately 12 years
of age), and conforms to European Standard ECE R
44/04.
• This approval is "Universal", which means that the
child car seat can be used on all types of cars. WAR-
NING! "Universal" means that it is compatible with
most, but not all car seats.
WARNING
This is a "Universal" child restraint device and is approved to ECE
Regulation No. 44, amendment series 04 standards. It is suita-
ble for use in vehicles and will fit most, but not all car seats.
A correct fit is likely if the vehicle manufacturer has declared that
the vehicle is capable of accepting a "Universal" child restraint for
this age group.
This child restraint has been classified as "Universal" under more
stringent conditions than those that were applied to earlier desi-
gns not displaying this notice.
Only suitable if the vehicle is fitted with a 3-point static or
3-point retractor safety belts approved to UN/ECE Regulation
No. 1 6, or other equivalent standard.
If in doubt, consult either the child restraint manufacturer or
the retailer.
All manuals and user guides at all-guides.com
8
RESTRICTIONS AND REQUISITES REGARDING THE
USE OF THE PRODUCT AND CAR SEAT
WARNING! Read these restrictions and requisites care-
fully to ensure the product and car seat are used safely: if
you don't the safety levels cannot be guaranteed.
This child seat is approved for seating children weighing
from 9 to 36 kilos only (from 9 months to approxima-
tely 12 yeas of age).
The car seat must be fi tted with a 3-point static or
3-point retractor safety belts approved to UN/ECE Regu-
lation No. 1 6, or other equivalent standards (diag. 5).
Never fi t the child car seat to a seat that is only equipped
with a 2-point safety belt (diag. 6)
The child car seat can be fi tted into the front passenger
seat or any other back seats. Never use this child car seat
fi tted into car seats facing sideways or facing rearwards
(diag. 7)
This product is expressly intended to be used only as a
child car seat; it should not be used indoors.
To ensure correct installation, check that the car seat hea-
drest does not interfere with the child seat's backrest.
FITTING THE CHILD CAR SEAT INTO THE CAR AND
SEATING A GR. 1 CHILD (9-18 KG)
WARNING! These instructions and diagrams are for the
installation of the child car seat on the right back seat.
To fi t the child car seat in other positions, carry out these
operations in the same order.
1. Place the child car seat onto the chosen forward fa-
cing car seat (diag. 8)
2. Thread the 3-point car safety belt through slot P on
the back of the child car seat (diag. 9A and 9B), and
pull it out of the slot on the other side of the backrest
(diag. 9C).
3. Click the car safety belt into the buckle so that both
the abdominal and the diagonal straps pass under the
armrest (diag. 10).
4. Pull the car safety belt fi rmly, ensuring that the child
car seat adheres correctly to the car seat (diag. 11), if
necessary, carry out this operation exercising some
pressure on the child car seat with your knee.
5. Check that the child car seat is fi tted fi rmly in place
and adheres correctly to the vehicle seat; check that
the seat belt is tight. If this is not the case, repeat the
fi tting procedure from the beginning (diag. 12).
WARNING! Always check that the seat belt is positioned
correctly and no parts are twisted.
NEVER fi t the car safety belt in any way other than that
indicated in these instructions.
When the child car seat is fi tted correctly, follow the in-
structions below to seat the child:
6. Press the restraint harnesses adjustment button H
and, at the same time grasp the lower part of the
child seat straps and pull in your direction as far as
possible (diag. 13)
7. Unfasten the child car seat restraint harness, pressing
the button on the buckle and move them to the sides
(diag. 1 4)
8. Make sure your child is seated comfortably on the