PRobLEm
burners burn with a yellow or orange flame, in
conjunction with the smell of gas. (this is normal for
the burner lighting tube.)
sear station
burner does not light.
®
General symptoms:
burner does not light.
or
burner has a small flickering flame.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
PRobLEm
rotisserie burner does not light.
General symptoms:
burner does not light.
or
burner has a small, flickering flame.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
PRobLEm
weber Grill out™ handle light does not light.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
32
SEAR STATIoN
Inspect spider/insect screens for possible obstructions .
(Blockage of holes .)
Did you ignite the two adjacent main burners? Refer to
"SEAR STATION
procedure .
Does burner light with a match?
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have been
activated .
.
®
RoTISSERIE TRoUbLESHooTING
Did you hold the burner control knob in and hold in for 20
seconds after burner ignited?
Did you wait to see the entire ceramic surface become
alight before counting 20 seconds?
Did you repeatedly use the snap ignition until the burner
ignited?
Does the igniter work? Do you see a spark when you
repeatedly use the snap igniter?
The excess flow safety device, which is part of the
barbecue to cylinder connection, may have been
activated .
.
®
GRILL oUT™ HANDLE LIGHT TRoUbLESHooTING
Are the batteries old?
Are the batteries installed correctly?
Is the lid in the up position with the power button ON?
Is the Weber
®
Is the Weber
®
correctly on the handle?
.
®
TRoUbLESHooTING
®
cHEcK
IGNITION & USAGE" for safe lighting
®
cHEcK
cHEcK
Grill Out™ Handle Light activated?
Grill Out™ Handle Light positioned
SoLUTIoN
Clean spider/insect screens .
Refer to "ANNUAL MAINTENANCE . "
Verify adjacent main burner ignition by visual inspection
of a flame .
m warninG: if ignition does not occur
in 5 seconds, turn burner control
off, wait 5 minutes to let the gas
clear before you try again.
If you can light burner with a match, then check the
Crossover
®
Channel on the sear burner .
Refer to "MAINTENANCE" for burner removal and
cleaning procedure .
Try manually lighting the burner . Refer to "SEAR
STATION
IGNITION & USAGE . " Call Customer Service .
®
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve to OFF . Disconnect
the regulator from the cylinder . Turn burner control knobs
to START/HI . Wait at least 1 minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to "MAIN BURNER
IGNITION . "
SoLUTIoN
Try to relight burner by holding burner control knob in;
continue holding in until 20 seconds after burner has
ignited .
When relighting burner by holding burner control knob
in, wait to see the entire ceramic surface become alight
before counting 20 seconds .
After waiting five minutes for gas to clear, try using the
snap igniter repeatedly until the burner ignites . Refer to
"ROTISSERIE BURNER IGNITION & USAGE . "
Try manually lighting the burner . Refer to "ROTISSERIE
BURNER MANUAL IGNITION . " Call Customer Service .
To reset the excess flow safety device, turn all burner
control knobs and the cylinder valve to OFF . Disconnect
the regulator from the cylinder . Turn burner control knobs
to START/HI . Wait at least 1 minute . Turn burner control
knobs to OFF . Reconnect the regulator to the cylinder .
Turn cylinder valve on slowly . Refer to "MAIN BURNER
IGNITION . "
SoLUTIoN
Replace batteries .
Refer to assembly illustration .
Light will activate when lid is open .
Press the power button .
Adjust position. Refer to assembly illustration.