Silverline 263302 Manual Del Usuario página 46

263456
• DO NOT store Lithium-Ion battery packs in a discharged state long term.
This can damage the Lithium-Ion cells. For long-term storage, store
batteries in a high charge state disconnected from the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles,
the battery's operation time and the maximum torque performance of the
drill will slightly reduce. This decline will continue until the battery has
minimal capacity after 500 charge cycles. This is normal and not a fault
with the battery pack
Fitting and removing sockets
1. Push a suitable socket on to the Square Drive (1). The Retaining Ball
(2) will keep the socket in place
2. To remove, pull the socket off the Square Drive
Note: Make sure any sockets used are hardened and suitable for use with
an impact driver.
Operation
Direction control
WARNING: NEVER change the direction of rotation while the tool is running.
This may cause permanent damage to the tool.
• The direction of rotation can be set using the Forward/Reverse Switch (5)
• For anti-clockwise rotation, push the switch to the right
• For clockwise rotation, push the switch to the left
Note: When the Forward/Reverse Switch (5) is in the central position,
the drill is locked and cannot be switched on. Use this setting as a safety
feature to prevent the drill from being switched on accidentally.
Switching on/off
WARNING: ALWAYS wear adequate personal protection equipment when
setting up and operating this machine.
1. To start the Wrench, squeeze the Trigger Switch (6)
2. The built-in Work Light LEDs (3) will illuminate when the Trigger
Switch is squeezed
Note: If the Trigger Switch cannot be pressed down, check that the
Forward/Reverse Switch (5) is not set to its middle position, which locks the
device (see 'Direction control').
3. The speed ofthe Wrench is controlled by the movement of the trigger:
the further the Trigger Switch is pressed down, the faster the Wrench
will run
4. Release the Trigger Switch to stop the machine
WARNING: If the power tool gets excessively hot in use, stop using the tool
immediately and allow to cool before continuing work. The cooling period
can be reduced by operating the Wrench at maximum speed with no load.
Always make sure the Motor Vents (4) are not blocked and do not allow
dust to enter the body of the tool through the Motor Vents; dust, especially
metallic dust, may damage or destroy the tool.
Accessories
• A full range of accessories including various types of sockets is
available from your Silverline stockist. Spare parts can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the mains power supply, before
carrying out any maintenance/cleaning of the charger. Remove the battery
before carrying out any maintenance/cleaning of the Wrench.
Note: Both the Wrench and the charger contain no user-serviceable parts.
If the device does not perform as outlined in this manual, return it to an
authorised Silverline service centre for repair.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre.
This advice also applies to extension cords used with this tool
10.8V Impact Wrench
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable
spray lubricant
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools
www.silverlinetools.com
7