G.seat Sling Adjustment; Adjusting Rear Seat Height; Cushion Installation; Rear Axle - Quickie QRI Manual De Instrucciones

Q R I
G. SEAT SLING ADJUSTMENT
Remove the screws and rear nut retaining the left side seat sling. Readjust VELCRO®-style
material to increase the tension in the seat sling. Replace screws and rear nut. If there is any
difficulty in reattaching the screws, try using a probe to help align the holes. Ensure that the
plastic saddles are under the seat rail in all fastener positions.
H. ADJUSTING REAR SEAT HEIGHT
To adjust rear seat height, loosen and remove the 4 cap screws ( I ) (2 per side) and nut plate ( J )
that secure the camber tube clamps (K) to the axle plates (L). Move both camber tube clamps
(K) to the desired height and reinstall the 4 cap screws that attach the camber tube clamps to
the axle bracket. Then follow the instructions for setting the toe-in/out to zero (Section J-3).
Tighten screws to 144 in-lbs. (16.3 Nm).
NOTE– Adjustment to rear seat height may also require caster angle adjustment. See Section L.
I. CUSHION
(Optional)
Place cushion on seat sling with VELCRO® side down. The beveled edge of the cushion
should be in front. Press firmly into place.
J. REAR AXLE
The most important adjustment on your Quickie wheelchair is the position of the rear axle.
The center of gravity and wheel camber are determined by the axle adjustment.
1. Center of Gravity Adjustment
The more you move your rear wheels forward, the more likely your chair will tip
over backwards. Always make adjustments in small increments, and check the
stability of your chair with a spotter to prevent a tip-over. We recommend that
you use anti-tip tubes until you adapt to the change and are sure you are not at
risk to tip over. Refer to additional Warnings in Section VI "Falls and Tip Over".
NOTE– Changes to the center of gravity may affect the rear seat height (Section H), toe-in/toe-out of the rear
wheels (Section J-3) and the squareness of the casters (Section L). If you change your center of gravity
position, re-adjust all of these settings if necessary.
NOTE– Adjusting your chair's center of gravity will require re-adjusting the location of the wheel locks
(if provided). See Section O for instructions on adjusting the wheel locks.
You can adjust your center of gravity position by moving the two axle plate and clamp assem-
blies (A) forward or rearward on the seat tube (B). Moving the axle plate clamps forward
shortens the wheelbase and lightens the front end, making your chair more maneuverable.
Moving the axle plates and camber tube rearward makes the chair more stable and less likely
to tip rearward.
To adjust the center of gravity location, remove both rear wheels. Loosen the 4 screws (C) (2
per side) that secure the axle plates (A) to the seat tubes. Slide both camber tube clamps for-
ward or rearward along the seat tube to the desired position. Make sure both sides are adjust-
ed symmetrically before tightening screws. Tighten screws to 144 in-lbs. (16.3 Nm).
Once the camber tube clamps are secured, attach the rear wheels, occupy the chair and
maneuver it with a spotter to get a feel for the new adjustment.
19
2. Wheel Camber
Wheel camber, shown as angular relationship (D), provides greater side-to-side stability due
to the increased width and angle of the wheelbase. It also allows for quicker turning and
greater access to the top of the handrims.
Wheel camber is determined by pairs of interchangeable camber plugs which are available
from your authorized supplier in 0º and 3° angles.
16
17
INSTALLATION
18
WARNING
19
X. SET-UP & ADJUSTMENT
16
17
L
J
I
K
18
A
C
B
19
A
D
122143 Rev. C