Shop-Vac H87 Serie Manual Del Usuario página 3

TOOL HOLDER ASSEMBLY
(Not standard with all models)
1. Replace tank cover and apply pressure with thumbs to
each latch until it snaps tightly in place. Make sure both lid
latches are clamped securely.
2. With rear of unit facing you, take tool holder and position it
with the tabs facing rear tank cover (Figure 2).
3. Press tabs of tool holder into the slots on mounting lugs
on rear of tank cover (Figure 3).
4. Press down until tabs snap into place.
DRY PICk UP
WARNING
– ALWAYS DISCONNECT THE PLUG FROM THE
WALL OUTLET BEFORE REMOVING THE TANk COVER.
CAUTION
– kEEP FILTERS CLEAN
EFFICIENCY OF THE VACUUM IS LARGELY DEPENDENT ON THE FILTER. A CLOGGED FILTER
CAN CAUSE OVERHEATING AND POSSIBLY DAMAGE THE CLEANER. CHECK THE FILTER
PERIODICALLY AND REPLACE AS REqUIRED.
INSTALLING FOAM SLEEVE AND
REUSABLE DRY FILTER
(Not standard with all models)
To pick up dust and dry material, you must install foam sleeve and reusable dry filter to ensure proper
filtration. NOTE: For H87S model filter retainer must be installed. If the vacuum has been used to
pick up liquids, the foam sleeve must be cleaned and dried before installing for dry pick up.
With tank cover in an upside down position, slide foam sleeve down over lid cage pulling until foam
sleeve completely covers lid cage (Figure 4). NOTE: Bottom of foam sleeve must be positioned
on the OUTSIDE of groove around lid cage for the reusable dry filter to fit properly (Figure 5, 6).
Center the reusable dry filter on lid cage (Figure 7), slide mounting ring down over filter until ring
is positioned against the ribs of the lid cage (Figure 8). The reusable dry filter should always be in
position over the foam sleeve for dry pick up. To remove the filter for cleaning, remove mounting ring
and filter from lid cage (Figure 9). To clean the reusable dry filter, shake off excess dirt and dust or
(depending on the condition of the filter) rinse with water. Allow the filter to dry completely and re-install.
DO NOT MACHINE WASH OR DRY.
IMPORTANT: BEFORE INSTALLING REUSABLE FILTER BE SURE THAT FOAM SLEEVE IS OUTSIDE
OF GROOVE AND AROUND LID CAGE (Figure 5, 6).
NOTE: ENSURE THAT THE MOUNTING RING IS COMPLETELY SECURE AND IN POSITION BY
PRESSING DOWN FIRMLY AROUND THE RING IN SEVERAL PLACES. BE SURE THE REUSABLE
DRY DISC FILTER COMPLETELY COVERS THE FOAM SLEEVE. CHECk TO ENSURE THAT ALL
EDGES OF THE REUSABLE DRY FILTER ARE SECURE UNDER THE MOUNTING RING.
4 5
7 8
INSTALLING THE CARTRIDGE FILTER
(Not standard with all models)
The cartridge filter can be used for wet or dry pick up; installation is the
same for both. For dry pick up be sure the opening of the inlet deflector
is facing the tank bottom (Figure 10). Use the cartridge filter in position
over the lid cage for most general dry material pick up. With the tank
cover in an upside down position, slide the cartridge filter down over
the lid cage, pushing until the filter seals against the cover (Figure 11).
Place filter retainer into the top of the cartridge filter, hold the tank cover
with one hand, turn the handle on the filter retainer clockwise to tighten,
locking the filter into place (Figures 12 & 13). To remove the filter for cleaning, again hold the
tank cover and turn the filter retainer counter-clockwise to loosen and remove, slide the cartridge
filter off the lid cage (Figures 14 & 15). To clean the cartridge filter shake or brush off excess
dirt or rinse (from the inside of the filter) with water, dry completely (approximately 24 hours) and
re-install. (Figures 16 & 17). Note: If the filter has been used for wet pick up, it must be cleaned
and dried before using for dry pick up.
2
3
(Not Standard with All Models)
1. Use for dry pick up only. Use in conjunction with cartridge filter for picking up soot, cement,
2. With cord disconnected from receptacle, pull latches in an outward motion and remove tank cover.
3. Unscrew hose locking-nut and remove hose from inlet (Figure 18).
4. Remove inlet deflector from deflector guide (Figure 19). NOTE: Hose must be removed before
5. With the opening of the inlet deflector facing the bottom of the filter bag, slide collection bag collar
6. Slide deflector with collection bag attached into deflector guide (Figure 21).
7. Reinsert hose into inlet and tighten locking-nut (Figure 22).
8. Fold bottom of collection bag to fit shape of tank.
When vacuuming fine dust, or powders of any kind (ex. plaster, drywall dust, cold ashes, concrete
dust, etc.)...a high efficiency drywall filter bag must be used. When vacuuming normal house-
6
hold dust and debris, standard household disposable filter bags may be used. These "large bag"
filters connect to the air inlet fitting on the inside of the vacuum tank.
SIZE
5-8 U.S. Gal (18.9-30.3L)
10-14 U.S. Gal (37.8-53L)
15-22 U.S. Gal (56.8-83.2L)
9
Remove ALL dirt and debris found in the tank. The vacuum requires only a
minimum of conversion when going from dry to wet pick up. Remove all dry
use filters from the vacuum. A clean cartridge filter may be used for vacuum-
ing small amounts of liquids. For best results when vacuuming large quanti-
ties of liquid, remove the cartridge filter. When vacuuming liquids containing
debris, it is recommended purchasing a foam sleeve and install over filter
cage; otherwise a foam sleeve is not required for wet pick up. Foam sleeve
10
and additional filters may be purchased by visiting our website at www.shop-
vac.com, contacting our customer service department, or purchasing at your
local Shop-Vac
motion. NOTE: Hose must be removed before inlet deflector can be taken out. Reinstall being
sure the opening of the inlet deflector is facing the top of the tank (Figure 23), misting may occur if
inlet deflector is not inserted properly. Misting in exhaust air may occur if the filter becomes saturat-
ed during wet pick up. If misting occurs, remove filter and allow to dry or, replace with another dry
filter to eliminate the misting and possible dripping of liquid around the lid. Turn the unit off imme-
diately upon completing a wet pick up job or when tank is full and ready to be emptied. Raise the
hose to drain any excess liquid into the tank. The interior of the tank should be periodically cleaned.
The foam sleeve should be cleaned periodically as described in the following steps:
1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place tank
2. Shake excess dust off foam sleeve with a rapid up and down movement.
11 12
14
15
LOOSEN
INSTALLING THE
DISPOSABLE FILTER BAG
plaster or drywall dust.
inlet deflector can be taken out.
over deflector matching notches of bag collar to tabs on inlet deflector, bag will only fit properly
one way (Figure 20).
18 19
21
WARNING FOR FINE DUST & POWDERS
FILTER SELECTION GUIDE
Fine dust Standard
Drywall Household
90671 90661/90532
90672 90662/90534
90673 90663/90533
WET PICk UP OPERATION
distributor. Remove inlet deflector from the deflector guide sliding in an upward
®
cover in an upside down position. Remove foam sleeve by sliding it up and off the lid cage.
NOTE: For H87S model filter retainer must be removed first.
13
TIGHTEN
16
17
20
22
90107 REUSABLE DRY FILTER AND MOUNTING RING
fits most Shop-Vac ® Wet/Dry Vacuums.
90585 FOAM FILTER SLEEVE fits most Shop-Vac
Vacuums.
23
® Wet/Dry