FALMEC Kristal Manual De Instrucciones página 17

Place the support bar (S) on the installation wall at a height (H) from the cooker indicated in the figure (Fig.
•
Use a spirit level to check the horizontal alignment and draw 2 marks at each end of the support bar, this is where the holes will be drilled (Fig.
•
Drill the holes, insert 2 expansion plugs (ø 8mm) and fasten the bar with the relative screws (V1) (Fig.
•
The fixing kit (screws, plugs, and brackets) supplied with the hood can only be used on masonry walls:
walls in a different material, assess other fixing systems keeping the wall resistance and weight of the hood in mind (indicated on page 3 ).
B
Phase page 5
Hook the hood onto the support bar (Fig.
•
Adjust the alignment of the hood by using the fixing screws (Fig.
•
scrolling.
C D
Phase and page 5
EXTERNAL EXHAUST HOOD VERSION (SUCTION)
If you wish, install a check valve (M) as illustrated in figure
•
Connect the air outlet connection of the hood to the external discharge with a suitable pipe.
•
HOOD VERSION WITH INTERNAL RECIRCULATION (FILTERING)
Check that the active carbon filters are assembled onto the hood, if not, install them as indicated in the instructions
•
If installed, remove the check valve assembled on the hood air outlet fitting (carry out the instructions described
•
E
Phase page 6
Insert the extension (H) in the chimney (G) (Fig.
•
With external exhaust (suction) versions, it is possible to insert extension (H) with the slots facing downwards so that they are not visible when the installation
•
height allows it.
F
Phase page 6
Slide the extension (H) until it is positioned at the desired height (Fig.
•
Following what is indicated in Fig.
•
Place the bracket (L) on the wall by following the line drawn on it. With a spirit level, check the horizontal alignment and mark the 2 drilling points at the ends (Fig.
•
Drill the holes, insert 2 expansion plugs (ø 6mm) and fasten the bracket (L) with the relative screws (V4) (Fig.
•
Tighten the extension (H) to the bracket (L) using screws (V5) (Fig.
•
Electrically power the hood in accordance with regulations in force.
•
OPERATION
WHEN SHOULD THE HOOD BE SWITCHED ON AND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airflow to convey fumes and vapours towards the suction surface. After cooking,
leave the hood operating until complete extraction of all vapours and odours. If required, by means of the Timer function, it is possible to set hood auto switch-off
after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
The first speed is a low consumption energy-saving way of keeping the air clean, the second speed is used in normal conditions, and the third speed is used when
there are strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The hood is assembled with two different types of filters: metal ones (washable) and active carbon ones (non-washable). The former must be cleaned every 30 hours
of use (the steady light indicates that they need to be washed), the latter are to be replaced every 3-4 months, depending on the use of the hood. For further
information, please read the chapter regarding "Maintenance".
HOOD VERSION WITH INTERNAL RECIRCULATION (FILTERING)
In this model, air passes through the active carbon filters to be purified and is then recycled into the kitchen environment.
Check that the active carbon filters are assembled onto the hood, if not, install them as indicated in the instructions
on page 7.
If the hood is set up with a filtering version, the check valve must not be assembled: remove it if it is on the air outlet fitting of the
motor (carry out operations described in the instructions
ASSEMBLY INSTRUCTIONS
A
Phase page 5
1
).
2
C
.
1
) and fasten the assembly to the body of the hood using screws (V3)(Fig.
2
, draw a line on the wall that will be used to position the bracket (L) correctly.
5
C
on page 5 in reverse order).
(only intended for personnel qualified to assemble the hood)
4
).
). The upper screw (B) adjusts the distance from the wall, the lower one (C) adjusts vertical
1
).
).
17
1
).
2
hould it be necessary to install the hood onto
s
H
on page 7.
C
on page 5 in reverse order).
2
).
4
).
H
3
- ).
3
.