Troubleshooting - Vollrath Mirage 7470110 Manual Del Operador

TROUBLESHOOTING

Problem
The equipment is on, but not heating
and the display is flashing.
Alarm is sounding.
The equipment suddenly stopped
working.
Display
Message Cause
Bad Pan The inset is not a Vollrath induction-ready inset or is the wrong size
Vollrath induction-ready inset.
HOT If the equipment is turned off, this is normal. It indicates the equip-
ment is still hot.
If the equipment is in use, the inset may be too hot.
F-2 The inset may be too hot.
F-1 The equipment may have overheated.
F-8
Other error Internal error.
codes
SERVICE AND REPAIR
Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or
replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services
for instructions.
When contacting Vollrath Technical Services, please be ready with the
item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
The Vollrath Company, L.L.C. Headquarters
1236 North 18th Street
Sheboygan, Wisconsin
53081-3201 USA
Main Tel: 800-624-2051 or 920-457-4851
Main Fax: 800-752-5620 or 920-459-6573
Canada Customer Service: 800-695-8560
Tech Services: techservicereps@vollrathco.com
www.vollrath.com
Might be Caused By
The inset is not a Vollrath induction-ready
inset or is the wrong size Vollrath induction-
ready inset.
Trouble with the electrical connection is
causing low input voltage.
An error.
The equipment may be too close to an
external heat source or the air intake may be
restricted.
The inset may be too hot.
Pujadas
Ctra. de Castanyet,
132 P.O. Box 121
17430 Santa Coloma de Farners
(Girona) – Spain
Tel. +34 972 84 32 01
info@pujadas.es
Course of Action
Replace the inset with the correct size Vollrath induction-ready
inset for the equipment. Vollrath induction-ready insets are
stamped "Induction Ready." Reset the equipment by turning it
OFF and then ON.
Make sure the plug is fully inserted into an electrical outlet that
matches the rating on the equipment's nameplate.
Make sure the electrical circuit is not overloaded.
See the Display Messages in the table below.
Relocate the equipment away from external heat sources. Clear
any obstructions to the air intake. Contact Vollrath Technical
Services if the problem persists.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Contact Vollrath Technical Services if the prob-
lem persists.
Course of Action
Replace the inset with the correct size Vollrath induction-ready
inset for the equipment. Vollrath induction-ready insets are
stamped "Induction Ready." Reset the equipment by turning it
OFF and then ON.
Allow the equipment to cool (about 5-10 minutes) before clean-
ing.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Do not place excessively hot food into the inset.
Do not an place excessively hot inset into the equipment. Con-
tact Vollrath Technical Services if the problem persists.
Remove the inset. Allow the inset and equipment to cool before
resuming use. Do not place excessively hot food into the inset.
Do not an place excessively hot inset into the equipment. Con-
tact Vollrath Technical Services if the problem persists.
Relocate the equipment away from external heat sources. Clear
any obstructions to the air intake. Contact Vollrath Technical
Services if the problem persists.
Contact Vollrath Technical Services.
WARRANTY STATEMENT FOR THE VOLLRATH CO.
This warranty does not apply to products purchased for personal,
family or household use, and The Vollrath Company LLC does not offer
a written warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or
distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs
from the date of the end user's original purchase date found on the
receipt. Any damages from improper use, abuse, modification or
damage resulting from improper packaging during return shipment for
warranty repair will not be covered under warranty.
For complete warranty information, product registration and new
product announcement, visit www.vollrath.com.
Vollrath of China
Vollrath Shanghai Trading
Limited
Room 201, Building A
Xin Yi Plaza
1618 Yi Shan Road
Shanghai, 201103
China, P.R.C.
Tel: +86-21-5058-9580
©
2018 The Vollrath Company L.L.C.
Vollrath de Mexico S. de R.L. de C.V.
Periferico Sur No. 7980 Edificio 4-E
Col. Santa Maria Tequepexpan
45600 Tlaquepaque, Jalisco |
Mexico
Tel: (52) 333-133-6767
Tel: (52) 333-133-6769
Fax: (52) 333-133-6768
Part No. 2350190-1 ml 6/28/18