Functional Description - Makita CJ102D Manual De Instrucciones

• Do not store the jacket, battery holder and battery
cartridge in locations where the temperature may reach
or exceed 50°C (122°F).
• Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
• Be careful not to drop or strike battery.
• Do not use a damaged battery.
• Follow your local regulations relating to disposal of
battery.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will also void
the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life
• Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
• Charge the battery cartridge with room temperature at
10°C - 40°C (50°F - 104°F).
• Let a hot battery cartridge cool down before charging it.
• Charge the battery cartridge once in every six months if
you do not use it for a long period of time.
• For an optimum life-time, the battery cartridge have to
be fully charged, after use.
SAVE THESE INSTRUCTIONS.
DESIGNATION OF PARTS (Fig. 1)
1. Power button
2. Battery holder pocket (Backside)
3. Power cable (Inside the battery holder pocket)
4. Hole for strap
5. Battery holder
(See the last part of this instruction manual for all the
illustrations.)
SPECIFICATIONS
Model
Temperature
adjustment steps
Material
USB power supply port
Operating time (h)
(With battery BL1040B)
Rated voltage (V)
Battery cartridge
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
4
CJ102D/CJ103D
3
Outer shell:
- Polyester (94%)
- Spandex (6%)
Inner shell:
- Polyester (100%)
DC 5V, 2.1A
Low APPROX. 14
Medium APPROX. 7.5
High APPROX. 4.0
DC 10.8 V
BL1015, BL1020B, BL1040B
• Specifications and battery cartridge may differ from
country to country.
• Operating time may differ depending on battery type
and usage condition.

FUNCTIONAL DESCRIPTION

Switch action
To turn on the jacket, push and hold the power button
(about 1.5 seconds). To turn off, push and hold the power
button again.
Temperature adjustment
There are three temperature settings (high, medium, low).
Three LED lights means that the temperature is set to
"high", two LED lights "medium", and one LED light "low".
When you switch on the jacket, the temperature is set to
"high". Each press of the power button cycles through the
jacket's temperature setting.
Indicating the remaining battery capacity
(Fig. 2)
(Only for battery cartridges with "B" at the end of the
model number.)
Press the check button (7) on the battery cartridge to
indicate the remaining battery capacity. The indicator
lamps (6) light up for few seconds.
Indicator lamps
Lighted Off
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
ASSEMBLY
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the battery holder and the
battery cartridge firmly may cause them to slip off your
hands and result in damage to the battery holder and
battery cartridge and a personal injury.
Installing or removing battery cartridge to
the battery holder (Fig. 3)
To install the battery cartridge (10), align the tongue on
the battery cartridge with the groove in the battery holder
and slip it into place. Insert it all the way until it locks in
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%