Installation; Venting Methods - ELICA ECL630S3 Guía De Instalación, Uso Y Mantenimiento

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Installation

• It is recommended that the vent system be installed before
hood is installed.
• If you are installing the optional backsplash with shelves
for heat lamps, follow the instructions included with that
product.
• If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall.
• Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
• Check that all installation parts have been removed from
the shipping carton.
1
Disconnect power.
2
Determine which venting method to use: roof or wall
exhaust.
NOTE: This hood is factory set to vent through the top air
exit. If you decide to use the rear vent exit, you have to
remove the rear vent cover and relocate it to the top vent
exit.
3
Select a flat surface for assembling the range hood. Place
covering over that surface.
Veting Methods
Outside Top exhaust
Vertical duct Ø 10" (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the cabinet's bottom or roof for ductwork, elec-
trical wiring and keyhole screw slots.
5
1
C
(133mm)
" (19 mm)
3
D
4
E
FRONT OF THE HOOD
ECL630S3
ECL136S3
A
30" (760 mm)
36" (912 mm)
B
C
D
E
F
3
" (90 mm)
9
1 6
G
H
CL
"
5
"
1
4
4
(133mm)
WALL
F
G
Ø 1"
(25.4 mm)
H
A
ECL142S3
ECL148S3
42" (1066 mm)
48" (1217 mm)
12" (305 mm)
1" (25.4 mm)
2
" (65 mm)
5
8
7
" (190 mm)
1
2
5
" (150 mm)
6
" (164 mm)
15
7
1 6
1 6
2" (50 mm)
3
" (89 mm)
1
2
Outside rear exhaust
Horizontal duct Ø 10" (25.4 cm)
Use the diagram or the hood as a template and mark the
locations on the wall for ductwork, electrical wiring and ke-
yhole screw slots.
F
E
J
G
Ø 1"
H
(25.4 mm)
I
ECL630S3
A
30" (760 mm)
B
C
D
E
3
" (87 mm)
7
1 6
F
2
" (75 mm)
15
1 6
G
H
I
J
1
Remove the grease filters.
2
Remove the blower mounting screws. Put the screws in a
safe place in order to use them again.
B
3
Set free the two blower springs from the top of the range
hood housing.
CL
TOP OF
D
C
C
D
E
THE HOOD
5
"
5
"
1
1
4
4
(133mm)
(133mm)
B
B
A
ECL136S3
ECL142S3
36" (912 mm)
42" (1066 mm)
9
" (250 mm)
7
8
4" (100 mm)
7
" (192.6 mm)
9
1 6
5" (127 mm)
5
" (147 mm)
13
1 6
5
" (135 mm)
5
1 6
7
" (192 mm)
1
2
2" (50 mm)
6
"(157 mm)
2
8
3
"(94 mm)
11
1 6
ECL148S3
48" (1217 mm)
6
" (167 mm)
9
1 6
5
" (149 mm)
7
8
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ecl136s3Ecl142s3Ecl148s3

Tabla de contenido