Operation - Muskoka 23-900-003 Manual De Instrucciones

Operation

NOTE: When the heat function is used for the first time, a slight odor may
be present. This is normal and should not occur again unless the heater is
not used for an extended period of time.
USING THE CONTROL PANEL
1. Check that the heater outlet grill is not covered or obstructed in
anyway, and make sure the power to the unit is switched on.
2. The fireplace can be accessed in two ways: Using the touchpad
control panel, or using the multifunction remote control unit.
3. Press the appropriate button to operate your fireplace:
1. Main Power Button: This button supplies power to
all of the fireplace functions. It must be turned on
for the fireplace to work.
2. Heater Control Button: This button controls the
heater ON/OFF. When the temperature unit is
set as 'F"or "C", the temperature scope are as
follows:
"F" =Fahrenheit temperature 86°F, 84°F, 82°F, 80°F,
78°F, 76°F, 74°F, 72°F, 70°F, 68°F, 66°F, 64°F, 62°F.
"C" =Celsius temperature 30°C, 29°C, 28°C, 27°C,
26°C, 25°C, 24°C, 23°C, 22°C, 21.C, 20°C, 19°C,
18°C, 17°C.
3. Flame Control Button: This button controls the
brightness of the flame effect with settings at
High, Medium, and Low. When the log set is first
turned on, the flame will come on at the highest
setting. The log set will remember the last flame
setting used and in later use the flame brightness
will start at that setting, unless power to the unit
has been interrupted. Each time the flame button
is pressed, the flame brightness decreases. The
only way to turn off the flame effect completely is
to turn off the main power button (1).
NOTE: After the fireplace has been operating, when the unit is turned off, the fan (not the heater) will continue
to run for about 1 minute to cool down the interior of the unit. During this time, you may feel cool air from the
blower outlet. This is normal and does not require any action. The fan will stop once the interior cools down.
IMPORTANT: Under normal operation, when power is interrupted from either an outage of from
unplugging unit from wall while still in operation, error code "EC" may appear on the LCD control
panel and the unit will cease operation. In order to reset, unplug the unit for 10 minutes, then plug
back in for normal operation in accordance with the Use and Care guide.
8
5 6
4. Timer Button: This button controls the ON/OFF
and 8-time setting from 1 H to 8 H. When the
Timer is first turned on, it will come on at the
shortest time setting (1 H). Each time the Timer
button is pressed, the time increases 1 hour,
up to the longest setting (8 hours). Once the
set time expires, all fireplace functions will be
automatically turned off.
5. Fahrenheit/Celsius Display: This button displays F
(Fahrenheit) or C (Celsius) depending on how the
temperature mode is set. When the fireplace is
turned on, the Fahrenheit (F) temperature will be
displayed. To switch from Fahrenheit to Celsius, or
vise-versa, when the HEATER is ON, hold HEATER
CONTROL button for 10 seconds. The fireplace
will remember the last temperature mode
setting, and in later use, the display will start at
that setting, unless power to the unit has been
interrupted.
6. Temperature/Timer Display: This LED display
shows the set point for the temperature and
timer functions. When either of these functions
is activated, the display reflects the set point
for five seconds and then fades to black. Any
change in the set point of the temperature or
timer will reactivate the display, which again
fades after five seconds.
4 2
1
4
3
2
3 1