Martin Yale intimus 45SC2 Instrucciones De Uso página 6

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
CONTROLS:
7 = Control display (Fig. 1)
"Oil cutters"
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on the
reverse button (4) (see description in "CUTTER
MAINTENANCE").
8 = Control display (Fig. 1)
"Door open"/ "Door malfunction"
a) "Door open"
Comes on if the door on the lower part of the
machine is opened. The machine switches
off automatically and cannot be started as
long as the door remains open.
b) "Electrical fault"
Flashes when there is an electrical fault in
the door sensor. The machine switches off.
Please contact your dealer.
9 = Control display (Fig. 1)
"Motor overload" /
"Electrical fault"
To find out what to do see the relevant description
under the "MALFUNCTION" section.
a) "Motor protection"
Comes on when the motor has been
overloaded and has switched off. The
machine cannot be started while the motor
is cooling down.
b) "Electrical fault"
Flashes when there is an electrical fault
inside the control board. At the same time the
function button (2) LED display
The machine switches off. Please contact
your dealer.
10 = Control display
"CD/DVD container full" (Fig. 1)
Comes on when the CD/DVD container is
full and must be emptied. The cutting unit for
reducing CD/DVD switches off. The emptying
procedure must be acknowledged on the
forward button (3).
Note: The cutting unit for reducing paper can
be used furthermore.
11 = Control display
"Paper collection bag full" (Fig. 1)
Comes on when the paper collection bag is
full and must be emptied. The cutting unit for
reducing paper switches off.
Note: The cutting unit for reducing CD/DVD
can be used furthermore.
12 = Paper feed slot (Fig. 3)
13 = CD/DVD feed slot (Fig. 3)
14 = Paper collection bag (Fig. 4)
15 = CD/DVD collection container (Fig. 4)
16 = Bag frame (Fig. 4)
17 = Oil reservoir (Fig. 4, 6)
6
7
8
2
fig. 1
OPERATION
The shredder may not be used as a step
ladder or as a seat. Danger of falling due
to breakage!
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to "Ready":
- Press the function button (2) briefly.
- The function button (2) LED display
for "Ready".
- The machine is ready for operation.
MATERIAL FEED:
Feed paper into the cutting mechanism through the
paper feed slot (12) (fig. 3).
Feed data carriers (CD, DVD or credit card) into the
cutting mechanism individually into the separate CD/
DVD feed slot (13) (fig. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
When shredding papers, do not shred CD/
DVD at the same time, and vice versa!
Note: For shredding transparent films, the machine
must be manually switched to forwards running (press
and hold the forwards button (3) for approx. 2 secs.).
By briefly pressing the function button (2) (Stop
function), the shredding process can be stopped at
any time. To continue, press and hold the forwards
button (3) for approx. 2 secs.
flashes.
If the machine is not used for a period of approx. 5
mins., it automatically switches off.
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL DATA
section!
Should the machine become overloaded,
follow the instructions under "MATERIAL JAM
IN MACHINE" under "MALFUNCTIONS".
Two separate collection containers ensure that
waste is separated properly.
EMPTYING THE
PAPER COLLECTION BAG (Fig. 4):
If the paper collection bag is full the machine switches
off. The control display
follows:
- Open the door. The control display
If there is still material in one of the feed slots, the
control display (6) also comes on.
- Pull out the bag frame (16) together with the
attached paper collection bag (14) and fitted CD/
DVD container (15) from the lower part of the
housing.
- Remove the CD/DVD container, take out the paper
collection bag and empty the contents. The control
display (11) goes out.
3
9
13
10
11
12
4
comes on
(11) comes on. Proceed as
(8) comes on.
5
fig. 3
6
- Attach the emptied bag to the bag frame (16), fit the
CD/DVD container and slide the frame together with
the bag and CD/DVD container back into the lower
part of the housing.
- Close the door. The control display
- If the control display (6) comes on, press the
forward button (3) briefly. The remaining material in
the feed slot is shredded and the display go out.
Note: The machine will only run if the door is closed.
EMPTYING THE CD/DVD
CONTAINER (Fig. 4):
Note: The "CD container full" is monitored by counting
the number of shredding processes performed.
If the number of CD's/DVD's pre-programmed into
the control unit (about 20) is shredded the machine
switches off. The control display
Proceed as follows:
- Open the door. The control display
and the forward button (3) LED display
the control display (10) flashes.
- Pull out the bag frame (16) together with the
attached paper collection bag (14) and fitted CD/
DVD container (15) from the lower part of the
housing, remove the CD/DVD container and empty
the contents.
- Press the forward button (3) briefly to acknowledge
that the CD/DVD container has been emptied. The
counting process begins at zero again. The control
display (10) and the forward button (3) LED
display go out.
- Fit the emptied CD/DVD container to the bag frame
(16) and slide the frame together with the bag and
container back into the lower part of the housing.
- Close the door. The control display
Note: The machine will only run if the door is closed.
DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure a continual,
effective destruction of the data carriers, the current
load level of the motor is displayed during the
shredding process by a coloured, diffuse light in the
feed slot as follows:
Green light: load < 50%
Yellow light: load 50 - 75%
Red light: load 75 - 100%
15
17 14
fig. 4
(8) goes out.
COLLECTION
(10) comes on.
(8) comes on
as well as
(8) goes out.
16