Troubleshooting - Blaupunkt 5VF5X00EWE Instrucciones De Uso

TROUBLESHOOTING

In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
PROBLEMS POSSIBLE CAUSES
Salt indicator Salt reservoir is empty. (After refill the salt
is lit indicator may remain lit for several wash cycles).
Rinse aid Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for several wash cycles). Refill dispenser with rinse aid (for more information - see page 14).
indicator is lit
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage.
The dishwasher
The dishwasher door is not closed.
won't start
ActiveDry pin is not pulled in.
or does not respond
Cycle is interupted by door opening for more
to commands.
than 4 seconds.
It does not respond to commands.
Display shows: 9 or 12 and On/Off LED is
blinking rapidly
The wash cycle has not finished yet.
The dishwasher
won't drain.
The drain hose is bent.
Display shows:
The sink drain pipe is blocked.
3 and On/Off LED is
blinking rapidly
The filter is clogged up with food residues.
The dishes are rattling against each
The dishwasher
makes excessive
An excessive amount of foam has been produced.
noise.
The crockery has not been arranged properly.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
The dishes are not
An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for use
clean.
The cap on the rinse aid compartment has not
been shut correctly.
The filter is soiled or clogged.
There is no salt.
The dishwasher
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
does not fill
the water.
The inlet hose is bent.
Display shows: H,
6 and On/Off LED is
The sieve in the water inlet hose is clogged; it is
necessary to clean it
blinking rapidly
Dishwasher
Drain hose positioned too low or siphoning into
finishes the cycle home sewage system.
prematurely.
Display shows: 15
Air in water supply.
and On/Off LED is
blinking rapidly
Policy and standard documentation and additional product information can be found by:
Visiting our website www.blaupunkt-einbaugeraete.com
•
• Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty
•
booklet). When contacting our After-sales Service, please state the codes provided on your
product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
at https://eprel.ec.europa.eu (available only on certain models).
SOLUTIONS
Refill reservoir with salt (for more information - see page 13).
Adjust water hardness - see table, page 13.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press START/PAUSE button and close the door within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/PAUSE and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug
the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program, press
START/PAUSE and close the door within 4 seconds. Please do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
After having carried out the verification and cleaning, turn off and turn
on the dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check
for siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
19
EN
SERVICE XXXXXXXXXX XXXXXXXXXXXX
XXXXXXXXXX
Model
I.C. XXXXXXXXXXXX S/N XXXXXXXXXXXX
XXXXXXXXXXXX
MADE IN EU [BAR-CODE AREA]
XXXXXXXXXXXX
FXXXXXX RMMDDXXXX
IEC 436
220-240V ~50Hz 0,05 - 1 MPa 14
MAX: 1900W 1800W TYPE:DWL-DEA701-B