Berner BACSDB-1 18V Manual Original página 13

ures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of chil-
u
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous
in the hands of untrained users.
Maintain power tools and accessories. Check
u
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
u
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
u
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Keep handles and grasping surfaces dry,
u
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unex-
pected situations.
Battery tool use and care
Recharge only with the charger specified by
u
the manufacturer. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
Use power tools only with specifically desig-
u
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
When battery pack is not in use, keep it away
u
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
battery terminals together may cause burns or a
fire.
Under abusive conditions, liquid may be ejec-
u
ted from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irrita-
tion or burns.
Do not use a battery pack or tool that is dam-
u
aged or modified. Damaged or modified bat-
teries may exhibit unpredictable behaviour res-
ulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or
u
excessive temperature. Exposure to fire or
temperature above 130°C may cause explosion.
1 609 92A 5NK • 9.4.20
English
Follow all charging instructions and do not
u
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
Service
English
Have your power tool serviced by a qualified
u
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Never service damaged battery packs. Ser-
u
vice of battery packs should only be performed
by the manufacturer or authorized service pro-
viders.
Safety Instructions for Drill/Driver
Safety instructions for all operations
Hold the power tool by insulated gripping sur-
u
faces, when performing an operation where
the cutting accessory or fasteners may con-
tact hidden wiring. Cutting accessory or
fasteners contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and
could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the max-
u
imum speed rating of the drill bit. At higher
speeds, the bit is likely to bend if allowed to ro-
tate freely without contacting the workpiece,
resulting in personal injury.
Always start drilling at low speed and with
u
the bit tip in contact with the workpiece. At
higher speeds, the bit is likely to bend if al-
lowed to rotate freely without contacting the
workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit
u
and do not apply excessive pressure.Bits can
bend causing breakage or loss of control, res-
ulting in personal injury.
Additional safety information
Secure the workpiece. A workpiece clamped
u
with clamping devices or in a vice is held more
secure than by hand.
Always wait until the power tool has come to
u
a complete stop before placing it down. The
application tool can jam and cause you to lose
control of the power tool.
Switch the power tool off immediately if the
u
application tool becomes blocked. Be pre-
pared for high torque reactions which cause
kickback. The application tool becomes
blocked when it becomes jammed in the work-
piece or when the power tool becomes over-
loaded.
English
English
English
English
English | 13