Lamp (Re)Placement; Overhead Rigging; Control Panel - BEGLEC JB Systems Light iMove 5S ELC Manual De Instrucciones

ENGLISH

LAMP (RE)PLACEMENT

In case of replacement of the lamp or maintenance, do not
open the fixture within 10 minutes until the unit cools
down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs,
fuses, etc.) When replacing parts, please only genuine
spare parts.
 Switch off the unit and unplug the mains cable.
 Wait for about 10 minutes until the unit has been cooled down.
 Use a screwdriver to unscrew the screw that closes lamp compartment of
the fixture.
HID Version
 On the inside you will see the lamp. Tear the lamp gently out of the
lamp holder.
 Unscrew the 2 wires from the wire terminal
 Install the 2 wires from the new lamp in the wire terminal and make
sure to fasten the terminals well.
 Press the new lamp gently in the lamp holder.
Attention! Check the label on the backside of the device or see
the technical specifications in this manual to know which lamp
should be used. Never install lamps with a higher wattage! Don't
touch the bulb inside the reflector of the lamp with bare hands!
This drastically shortens the lifespan of the lamp. If you touched
the lamp, clean it with a cloth and a little denatured alcohol. Wipe
the lamp off before installing.
 Be sure that the wires don't touch the lamp.
 Close the lamp compartment with the screw.
 Done!
ELC Version
 On the inside you will see the lamp socket. Tear the lamp socket
gently out of the lamp compartment.
 Unplug the old lamp. Hold the lamp socket while unplugging the lamp instead of pulling the cable!
 Hold the lamp socket while pressing the new lamp gently in the socket.
Attention! Check the label on the backside of the device or see the technical specifications in this manual
to know which lamp should be used. Never install lamps with a higher wattage! Lamps with higher wattage
generate temperatures the device was not designed for. If the device uses a lamp transformer, it will burn
due to current overload.
 Don't touch the bulb with bare hands! This drastically shortens the lifespan of the lamp. If you touched the
lamp, clean it with a cloth and a little denatured alcohol. Wipe the lamp off before installing.
 Put the new lamp back inside the unit. Be sure that the wires don't touch the lamp.
 Close the lamp compartment with the screws.
 Done!
JB SYSTEMS®
OPERATION MANUAL
3/68 iMove 5S
ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
HOW TO SET UP THE UNIT

CONTROL PANEL:

1. DISPLAY: To show the various menus and the selected functions.
2. LEDs
DMX On DMX input present
MASTER On Master Mode
SLAVE On Slave Mode
SOUND Flashing Sound activation
3. BUTTONS
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
JB SYSTEMS®
OPERATION MANUAL
4/68 iMove 5S