Switching On And Off - Black and Decker FSM1620S Manual De Instrucciones

Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (4) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down. (approximately five
u
minutes)
Place the front of your shoe onto the carpet glider removal
u
tab (15) and press down firmly.
Lift the steam mop up off the carpet glider (11).
u
Caution! Always place your steam mop with the handle (4) in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Fitting a scent pack (Fig. J & K)
Warning! Return the handle (4) to the upright position and
turn the steam mop 'OFF'. Wait until the steam mop cools
down. (approximately five minutes).
Slide the door release button (20), the door will open.
u
Place the scent pack into the cavity (21).
u
Close the door (22) py pushing it firmly down.
u
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.

Switching on and off

To switch the appliance on, press the ON/OFF button (1).
u
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is first turned on the water res-
ervoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
To switch the appliance off, press the ON/OFF button (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
(Original instructions)
Autoselect Technology
TM
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning opera-
tion.
Using the Autoselect dial (2), choose from one of the follow-
TM
ing applications:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Hints for optimum use
General
Caution! Never use the steam mop without first attaching a
cleaning pad.
During use you can use the cable management clip (9) to
u
keep your cable out of the way of the work area..
Always vacuum or sweep the floor before using the steam
u
mop.
The easiest way to use the machine is to tilt the handle to
u
a 45˚ angle and clean slowly, covering a small area at a
time.
Do not use chemical cleaners with your steam mop. To
u
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam cleaning
Place a cleaning pad (6) on the floor with the 'hook & loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(6).
Connect the steam mop to the mains.
u
Turn the Autoselect dial (2) to the required setting.
TM
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
Pulling the handle (4) back will activate the steam pump.
u
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
ENGLISH
dial (2) which
TM
5