Monacor International WSA-10BT Manual De Instrucciones página 3

➀ Power LED: LED keeps flashing = no signal pairing
LED lights permanently = wireless connection
Bluetooth Receiver
These instructions are intended
for users without any specific
technical knowledge.
read these instructions carefully
prior to operating the unit and
keep them for later reference.
1 Applications
The Bluetooth receiver WSA-10BT
is used for wireless connection be-
tween a Bluetooth signal source
(e. g. notebook, smartphone, tab-
let PC) and an audio system. Thus,
audio files replayed on the Bluetooth
signal source can be reproduced via
the audio system connected to the
WSA-10BT.
The WSA-10BT supports the
signal transmission aptX
will substantially improve the audio
quality.
2 Safety Notes
The units (receiver and power supply
unit) correspond to all relevant di-
rectives of the EU and are therefore
marked with .
WARNING The power supply unit
uses dangerous mains
voltage. Leave servic-
ing to skilled personnel
only. Inexpert handling may result
in electric shock.
•
The units are suitable for indoor
use only. Protect them against
dripping water and splash water,
high air humidity and heat (admis-
sible ambient temperature range:
0 – 40 °C).
•
Do not operate the receiver or im-
mediately disconnect the power
supply unit from the socket
1. if the units are visibly damaged,
2. if a defect might have occurred
after a unit was dropped or suf-
fered a similar accident,
3. if malfunctions occur.
In any case the units must be re-
paired by skilled personnel.
1
•
For cleaning only use a dry, soft
cloth; never use water or chemi-
cals.
•
Please No guarantee claims for the units
and no liability for any resulting
personal damage or material dam-
age will be accepted if the units
are used for other purposes than
originally intended, if they are not
correctly connected or if they are
not repaired in an expert way.
If the units are to be put
out of operation definitive-
ly, take them to a local re-
cycling plant for a disposal
which is not harmful to the
environment.
3 Operation
which
®
1) Connect the Bluetooth receiver
to the audio system using the
digital output "Toslink" (2) or
"Coaxial" (3) or the analog out-
put "Analog" (4). To connect the
output "Analog", two different
audio cables are supplied.
2) Connect the power supply unit
provided to the jack "DC" (5) and
to a mains socket (230 V/ 50 Hz).
Thus, the receiver is switched on.
The status LED (1) starts flashing.
If you use a power strip with
on / off switch, it will be easier to
switch the receiver on and off.
3) Activate the Bluetooth function at
the Bluetooth signal source and
pair the signal source with the
WSA-10BT (refer to the manual
of the signal source, if required).
If a PIN code is re quested, enter
"0000".
Notes:
1. On the display of the Bluetooth
signal source, the WSA-10BT is in-
dicated as "BTAD01".
2. To allow signal transmission, the
Bluetooth signal source must use
the profile A2DP.
3. To ensure the best audio quality,
the Bluetooth signal source should
Toslink
2
➁ , ➂ , ➃ Audio outputs ➄
4) As soon as the Bluetooth signal
4 Specifications
Frequency range: � �20 – 20 000 Hz
THD: � � � � � � � � � � �0�05 %
Channel
separation: � � � � � �45 dB
S / N ratio: � � � � � � �≥ 90 dB
Bluetooth
Power supply: � � � �5 V (⎓) / 150 mA via
Dimension: � � � � � �91 × 25 × 57 mm
Weight: � � � � � � � � �60 g ( w/o power supply
Outputs
Subject to technical modification.
Coaxial Analog DC
3 4 5
Jack to connect the power supply unit
support the signal transmission
aptX .
®
source has been paired with the
WSA-10BT, the status LED (1) will
light permanently. Start the audio
reproduction at the signal source.
If a signal source was already
paired with the WSA-10BT and
then disconnected, this signal
source will automatically
paired again as soon as it enters
the reception range of the WSA-
10BT. The WSA-10BT is able to
store up to 10 Bluetooth signal
sources for automatic pairing.
However, automatic pairing may
not work with every signal source.
Version: � � � � � � �4�0
Profile: � � � � � � � �A2DP
Operating range: 10 – 20 m, depending
on signal source
power supply unit pro-
vided and connected to
100 – 240 V, 50 / 60 Hz
unit)
digital: � � � � � � � �optical output
(TOSLINK)
coaxial output (RCA)
analog: � � � � � � �3�5 mm stereo jack, 2 V
be
3