ETI SLTR-400W-52KLM-7-50K-MV-30D Manual De Uso Y Cuidado

USe anD CaRe GUiDe
SpoRTS LiGHTinG
noTe: Keep your receipt and these instructions for proof of purchase.
WaRninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION
noTiCe: This product is compatible with the following three types of dimming methods: (1) 1-10VDC dimming. (2) PWM dimming.
(3) Resistor dimming. User chooses the wiring, dimming method and installation.
Shut off power at the electrical panel before beginning the installation.
1
Remove existing fixture and set aside to recycle in accordance with local requirements.
2
POLe MOUNTINg
S1
400W
600W
1000/
1200W
Drill two holes on the mounting bar.
3a
10°
10°
If needed, adjust the projection angle and tighten
6a
the adjustment screw.
DISc HOLDer INSTALLATION
Use screws to attach the
3b 4b
fixture to the disc holder
but don't tighten the
screws.
Use a screwdriver to attach the shield to the
7b
fixture.
Make the electrical connections. See the
8b
electrical connections section of the manual
for more information.
Model & Certification #
60502261
60505261
60504261
60501361
60505361
60511461
60502461
60506461
60503461
7 1/4"
8 5/8"
8 5/8"
Attach the fixture to the crossbar and secure it with
4a
nuts, spring washers and flat washers.
M16*30 M12*30
Adjust the lighting direction, up to
360 degrees, tightened the screws
once the adjustment is complete.
DrIver INSTALLATION SecTION 1
Once the fixture is securly mounted attach the
1
standard driver next to the fixture.
60511561 60511861
60502561 60502861
60505561 60506861
60503561 60503861
60502661 60511961
60505661 60502961
60504661 60505961
60501761 60503961
60505761
Nut
Spring Washer
Flat Washer
M16
Use a screwdriver to attach the shield
7a
to the fixture.
Adjustment
Screw
Hex Wrench
Open-end
Wrench
Use a wrench and a hex wrench to
5b
loosen the adjustment screw used to
adjust the angle.
part #
SLTR-400W-52KLM-7-50K-MV-30D
SLTR-400W-52KLM-7-50K-MV-40D
SLTR-400W-52KLM-7-50K-MV-120D
SLTR-600W-78KLM-7-50K-MV-15D
SLTR-600W-78KLM-7-50K-MV-40D
SLTR-1000W-130KLM-7-50K-MV-12D
SLTR-1000W-130KLM-7-50K-MV-30D
SLTR-1000W-130KLM-7-50K-MV-45D
SLTR-1000W-130KLM-7-50K-MV-60D
SLTR-1200W-156KLM-7-50K-MV-15D
SLTR-1200W-156KLM-7-50K-MV-30D
SLTR-1200W-156KLM-7-50K-MV-40D
SLTR-1200W-156KLM-7-50K-MV-60D
PAckAge cONTeNTS
Part Description
A Fixture Housing
Use a wrench and a hex wrench to loosen the
5a
adjustment screw used to adjust the angle.
Make the electrical connections. See the electrical
8a
connections section of the manual for more
information.
10°
If needed, adjust the projection angle and
6b
tighten the adjustment screw.
Connect the DC connector and port together.
2
Now see electrical connection section.
SLTR-400W-52KLM-7-50K-HV-30D
SLTR-400W-52KLM-7-50K-HV-40D
SLTR-400W-52KLM-7-50K-HV-120D
SLTR-600W-78KLM-7-50K-MV-15D
SLTR-600W-78KLM-7-50K-MV-40D
SLTR-1000W-130KLM-7-50K-MV-12D
SLTR-1000W-130KLM-7-50K-MV-30D
SLTR-1000W-130KLM-7-50K-MV-45D
SLTR-1000W-130KLM-7-50K-MV-60D
SLTR-1200W-156KLM-7-50K-MV-15D
SLTR-1200W-156KLM-7-50K-MV-30D
SLTR-1200W-156KLM-7-50K-MV-40D
SLTR-1200W-156KLM-7-50K-MV-60D
Quantity
1
Adjustment Screw
Hex Wrench
Open-end
Wrench
10°