Introduction; Layout (Fig. 1,2); Scope Of Delivery; Proper Use - Dexter DX50V Traducción Del Manual De Instrucciones Original

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 47

1. Introduction

MANUFACTURER:
Adeo Services
135 rue Sadi Carnot
CS 00001
59790 Ronchin
France
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non­compliance of the operating instructions,
• Repairs by third parties, not by authorized ser­
vice technicians,
• Installation and replacement of non­original
spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non­compliance of the electric regu­
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating
instructions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities
in accordance with the recommendations. The
operating instructions contain important information
on how to operate the machine safely, profession­
ally and economically, how to avoid danger, costly
repairs, reduce downtimes and how to increase reli­
ability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula­
tions that apply for the operation of the machine
in your country. Keep the operating instructions
package with the machine at all times and store it in
a plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before oper­
ating the machine and carefully follow its informa­
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associated
dangers. The minimum age requirement must be
complied with.
18 | GB

2. Layout (Fig. 1,2)

Drain plug for condensation water
1.
Pressure vessel
2.
Transport handle
3.
Supporting foot
4.
Quick­lock coupling (tank pressure)
5.
Pressure gauge (for reading the preset vessel
6.
pressure)
Pressure regulator
7.
ON/OFF switch
8.
9.
Wheels
10. Quick­lock coupling (regulated compressed
air)
11. Safety valve
12. Pressure regulator attachment
A Threaded pins, 4x
B Hexagonal bolt, 2x
C Washers for feet, 4x
D Bracket
E Washers for wheels, 4x
F Hexagonal nuts for feet, 2x
G Hexagonal nuts for wheels, 2x
H Spring washer, 2x
I Flange screw, 2x
J Philips screw, 2x

3. Scope of delivery

Open the packaging and remove the device
carefully.
Remove the packaging material as well as the
pack aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for
transport damage.
If possible, store the packaging until the war­
ranty period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal­
lowing and suffocation!

4. Proper use

The compressor is designed to generate com­
pressed air for compressed­air driven tools which
can be driven with an air volume of up to approx.
120 l/min (e.g. tire inflator, blow-out pistol and
paint spray gun). Due to the limited air output it is
not possible to use the compressor to drive tools
with very high air consumption (for example orbital
sanders, rod grinders and hammer screwdrivers).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

39061389533906138850

Tabla de contenido