Tabla De Contenido; Install 4 Screws In Each Corner On Both Sides Of; For Gates With; For Screw Placement - Barrette BOM-34107025 Instrucciones De Instalación

8.
NOTE:
Different gate styles may have various rail
sizes. Check rail sizes and hole placements
before installing screws.
Once gates are square mark screw locations on
each upright (Fig. 10). Use screw con gurations
listed below:
For Gates With 7" Rails:
Install 4 screws in each corner, on both sides of
gate as shown (Fig. 11).

For Gates with 5

Install 4 screws in each corner on both sides of
gate as shown (Fig. 12).
For Gates With 2
Install 2 screws in each corner on both sides
of gate as shown, except where hinges will be
located (Fig. 13).
For 7" rails use the For 7" rails use the For 7" rails use the

following measurement

following measurement following measurement following measurement following measurement following measurement following measurement following measurement following measurement following measurement
for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement:
6 ⁄ ⁄ " ⁄ ⁄
1 1 1
4 4
⁄ ⁄ ⁄ ⁄ "
3 3 3
4 4
1 ⁄ ⁄ ⁄ ⁄ "
1 1 1
4 4
Upright Upright
2 ⁄ ⁄ ⁄ ⁄ "
1 1 1
2 2
9.
Install upright caps onto the top of each upright
with provided vinyl cement (Fig. 14).
10.
Install Boerboel
instructions for privacy gates; make sure hinges
are centered between the screws. For all gates,
make sure hinges are installed on upright on
the opposite side of the "leg" of the aluminum
P-channel insert. (Fig. 15).
6
⁄ ⁄ ⁄ ⁄ " Rails:
1 1 1
2 2
⁄ ⁄ " Rails: ⁄ ⁄
3 3 3
4 4
For 5 For 5 For 5 For 5 For 5 For 5 ⁄ ⁄ ⁄ ⁄ ⁄ " rails use the " rails use the " rails use the " rails use the
Fig. 11 1 1 1 1
2
following measurement following measurement following measurement following measurement following measurement following measurement following measurement following measurement following measurement following measurement

for screw placement:

for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement: for screw placement:
Rail Rail
7"
1 ⁄ ⁄ ⁄ ⁄ "
1 1 1
4 4
2 ⁄ ⁄ ⁄ " ⁄
1 1 1
2 2
hinges according to hardware
®
For 2 For 2
Fig. 12
following measurement following measurement
for screw placement: for screw placement:
5 ⁄ ⁄ " ⁄ ⁄
1 1 1
2 2
Rail Rail
4 ⁄ ⁄ ⁄ ⁄ "
3 3 3
4 4
⁄ ⁄ ⁄ " ⁄
3 3 3
4 4
Upright Upright
⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ " rails use the " rails use the
3 3 3
4 4 4
2 ⁄ " ⁄ ⁄ ⁄
1 1 1
2 2
Upright Upright
1 ⁄ ⁄ ⁄ ⁄ "
1 1 1
4 4
1 ⁄ ⁄ ⁄ ⁄ "
3 3 3
8 8
2 ⁄ " ⁄ ⁄ ⁄
3 3 3
4 4
P-Channel
Top View of Aluminum P-Channel
and Hinge Orientation
Fig. 10
Fig. 13
Rail Rail
Fig. 14
Fig. 15
"Leg"